Since the concept of active suspensions appeared, its large possible benefits has attracted continuous exploration in the field of railway engineering. With new demands of higher speed, better ride comfort and lower maintenance cost for railway vehicles, active suspensions are very promising technologies. Being the starting point of commercial application of active suspensions in rail vehicles, tilting trains have become a great success in some countries. With increased technical maturity of sensors and actuators, active suspension has unprecedented development opportunities. In this work, the basic concepts are summarized with new theories and solutions that have appeared over the last decade. Experimental studies and the implementation status of different active suspension technologies are described as well. Firstly, tilting trains are briefly described. Thereafter, an in-depth study for active secondary and primary suspensions is performed. For both topics, after an introductory section an explanation of possible solutions existing in the literature is given. The implementation status is reported. Active secondary suspensions are categorized into active and semi-active suspensions. Primary suspensions are instead divided between acting on solid-axle wheelsets and independently rotating wheels. Lastly, a brief summary and outlook is presented in terms of benefits, research status and challenges. The potential for active suspensions in railway applications is outlined.
12 June 2018 in IEEE Transactions on Industrial Informatics
Estimating communication latency is a challenging task in the applications of industrial Internet of Things (IIoT). Mobile convergecast, as a many-to-one communication pattern, has been recently explored in mobile sensor networks (MSNs) for industrial IoT, where sensor nodes are usually in mobile status, and report the sensed data regularly or randomly to one or more stationary sinks through multi-hop routing path. As convergecast becomes increasingly relevant for industrial sensing and monitoring, a critical part of empowering information aggregation is to maintain consistent transmission. Path duration is one important component of end-to-end delay for communications along then path. In this paper, a probabilistic model for mobile convergecast has been proposed and evaluated to capture path duration times, by considering parameters including network models, sensor network scope, and mobility patterns of network elements. Our simulation has verified the proposed model can provide a feasible analysis of end-to-end delays in IIoT implementing convergecast.
Semi-active suspensions are seen as a promising technology to improve ride quality in high-speed railway vehicles as they provide substantial benefits not achievable through an optimisation of the passive suspension while avoiding some drawbacks of full-active control. Previous works showed that semi-active primary suspensions (SAPS) offer significant improvement of ride quality. However, published implementations of this concept did not consider the coupling effects between car-body and bogie vibrations, which play a decisive role in the success of control strategies for SAPS. This paper provides a comprehensive analysis of SAPS to improve vehicle ride comfort, with special attention to the mitigation of car-body bending vibration. A vehicle model considering the coupling of car-body bending and bogie pitch is proposed and used for the synthesis of an LQG controller. The performance of the semi-active suspension and controller is assessed using a detailed flexible multibody system of a high-speed vehicle. The proposed control scheme is shown to be highly effective in reducing car-body vibration in the entire frequency range of interest from 1 Hz to20Hz. A remarkable ride comfort improvement is found in the entire speed range from 150 km/h to 350 km/h.
The recent tendency to reduce the weight of car bodies is posing a new challenge to vertical ride quality, since the vibrations related to car-body vertical bending modes affect heavily passengers’ comfort and cannot be fully mitigated by conventional vehicle suspensions. In this work, four mechatronic suspensions, considering active and semi-active technologies in secondary and primary suspensions, are compared to show their relative merits. LQG and H∞ model-based control strategies are established in a consistent way for each suspension scheme to perform a comparative assessment of the four concepts on objective grounds. A two-dimensional 9-DOF vehicle model is firstly built, using a simplified representation of car-body bending modes; this model is also used to design the model-based controllers. The comparison of the four mechatronic suspension schemes based on the 9-DOF model shows that full-active secondary suspension is the most effective solution whilst semi-active primary suspension is also effective in terms of mitigating car-body bending vibration. Then, a three-dimensional flexible multibody system (FMBS) vehicle model integrated with a finite-element car-body is considered to allow a more detailed consideration of the vehicle’s vibrating behaviour. The results of the FMBS model show a good agreement to the results of the 9-DOF model and the relative merits of the four mechatronic suspension schemes as found from the previous analysis are basically confirmed, although the FMBS model is more suited for a quantitative assessment of ride quality.
Active wheelset steering promises an attractive cost–benefit ratio and is highly likely to be implemented in the future. Previous studies investigated the steering effect simply through a wear index like wear number. However, a wear index cannot predict how much the material removal on wheels can be reduced, and it is unable to reveal the wear pattern. This paper builds an iterative wear model to predict wheel wear evaluation under the presence of an active steering system. Three active steering schemes are proposed, and they are compared in terms of wheel wear evolution. To quantify the steering effectiveness, two factors are created to, respectively, evaluate economic impacts and satisfaction of three steering schemes. Finally, a simplified method based on traditional wear indices is compared with the established iterative wear calculation method to examine the applicability and tolerance of the simplified method.