Wetting properties of Sn-Zn and Zn-Al alloys on Cu and Al substrates were studied. Spreading tests were carried out for 3 min, in air and under protective atmosphere of nitrogen, with the use of fluxes. In the case of Zn-Al eutectic, spreading tests were carried out at 460, 480, 500, and 520 °C, and in the case of Sn-Zn eutectic at 250, 300, 350, 400, 450, and 500 °C, respectively. Solidified solder/substrate couples were cross-sectioned and subjected to microstructure examination. The spreading tests indicated that the wetting properties of eutectic Sn-Zn alloys, on copper pads do not depend on temperature (up to 400 °C), but in the lack of protective atmosphere, the solder does not wet the pads. Wettability studies of Zn-Al eutectic on aluminum and copper substrates have shown a negative effect of the protective nitrogen atmosphere on the wetting properties, especially for the copper pads. Furthermore, it was noted that with increasing temperature the solder wettability is improved. In addition, densities of liquid solders were studied by means of dilatometric technique.
14 November 2005 in Monatshefte für Chemie - Chemical Monthly
Solders for ultrahigh-temperature applications were defined by Vianco as those able to sustain working conditions with temperatures as high as 573 K, with momentary temperature rise up to 623 K. Zn-Al eutectic alloy (12 at.% Al) fits such defined criteria with respect to its melting temperature. It was found that small additions of indium to Zn-Al eutectic lower its melting temperature. The aim of this work is to assess if and to what extent thermal properties and wetting behavior are affected. It was found that addition of In increases electrical resistivity and coefficient of thermal expansion value. Wetting angles on Cu and Al substrates of liquid Zn-Al eutectic-based alloys containing up to 1.5 at.% of In were studied with the sessile drop method, after wetting at 773 K in the presence of flux. A decrease of apparent wetting angle was observed with increasing concentration of In. After wetting tests solidified alloy-substrate couples were cross-sectioned and examined with scanning electron microscopy coupled with electron dispersive X-ray analysis.
Thermal expansion and electrical resistivity of alloys based on Sn-Zn eutectic with 0.5, 1.0, 1.5, and 4.0 wt.% additions of In were studied. Thermal expansion measurements were performed using thermomechanical analysis tester over 223-373 K temperature range. Electrical resistivity measurements were performed with four-probe method over 298-423 K temperature range. The electrical resistivity of alloys increases linearly with temperature and concentration of In; also coefficient of thermal expansion of the studied alloys increases with In concentration. Scanning electron microscopy revealed simple eutectic microstructure with In dissolved in Sn-rich matrix. The results obtained were compared with the available literature data. Spreading tests on Cu of Sn-8.8Zn alloys with 0.5, 1.0, and 1.5 at.% of In were performed. Wetting tests were performed at 250 °C, by sessile drop method, by means of flux, and wetting times were 3, 8, 15, 30, and 60 min. In general, no clear effect of wetting time on spreading was observed.
6 April 2012 in Soldering & Surface Mount Technology
Purpose: The purpose of this paper is to study the effect of copper concentration in near‐eutectic liquid SAC solders on their thermophysical properties: viscosity, surface tension, density; as well as wetting behavior on copper substrates at 523 K.Design/methodology/approach: Viscosity, surface tension, and density were studied over a broad range of temperatures with the recently developed Roach‐Henein method. The obtained results were compared with the data from modified capillary, maximum bubble pressure, wetting balance and dilatometric measurements. Wetting angles measured with wetting balance method were compared with the results of sessile drop measurements.Findings: The results obtained indicate that increasing concentration of copper in the alloy results in higher density, surface tension and viscosity, but differences resulting from copper concentration on wettability are relatively small. At 523 K, the density is: 7.097, 7.186, 7.232 g cm−3, the surface tension is: 538.1, 553.5, 556.7 m Nm−1, the viscosity is: 2.173, 2.227, 2.467 mPas, respectively, for alloys containing 0.41, 1.01 and 1.61 wt% of Cu. Wetting angles on copper substrates are similar within a margin of error for all compositions. The results of present study are compared with the available literature data and a relatively good agreement is observed.Originality/value: This paper provides the data of thermophysical properties of widely‐used SAC solders including viscosity, of which there is little data in the literature. It is confirmed that the increased copper concentration increases viscosity, yet this effect is small and does not correlate with the wetting behavior.