Achieving high performance in synchrotron radiation light sources demands increased precision in fiducialization and alignment of insertion devices (IDs). Conventional sensor systems utilizing Hall probes for high-precision magnetic field measurements face limitations in determining the absolute position of the magnetic center of IDs. In this paper, the Magnetic Landmark (MLK), a novel solution based on a magnetized block structure, is designed to address this challenge. The MLK serves as an intermediary, establishing contact between the magnetic center of IDs and their externally accessible fiducials, thus enabling high-precision alignment. Through analysis of magnetic field distribution, self-calibration precision, and practical application of the MLK, the following conclusions are drawn: when the Hall probe is positioned within 0.5 mm of the magnetic field zero point inside the MLK, the measurement accuracy of the zero point for normal and skew quadrupole magnetic fields reaches 7 and 2 μm, respectively. Additionally, the self-measurement accuracy of the MLK is 10 and 4 μm in the transverse and vertical directions, respectively. These accuracies meet our usage requirements. The MLK demonstrates efficacy in aligning the magnetic center of High Energy Photon Source (HEPS) In-air undulators, achieving alignment accuracies of 16 μm in the transverse direction and 11 μm in the vertical direction, surpassing the 30 μm accuracy stipulated in the physical design. Furthermore, the device proves applicable for measuring the magnetic center of other types of HEPS insertion devices, including Cryogenic undulators.
Air separation units (ASUs) are power-intensive devices on the electricity demand side with significant potential for large-scale energy storage. Liquid air energy storage (LAES) is currently a highly promising large-scale energy storage technology. Coupling ASU with LAES equipment can not only reduce the initial investment for LAES, but also significantly lower the operating electricity costs of the ASU. This study proposes a novel modular-integrated process for coupling an externally compressed ASU (ECAS) with LAES. The core advantages of this integrated process are as follows: the liquefaction unit’s storage capacity is not constrained by the ASU surplus load capacity and it integrates cold, heat, electricity, and material utilization. Taking an integrated system with 40,000 Nm3/h oxygen production capacity as an example, under liquefaction pressure of 90 bar and discharge expansion pressure of 110 bar, the system achieves its highest electrical round trip efficiency of 55.3%. Its energy storage capacity reaches 31.32 MWh/104 Nm3 O2, exceeding the maximum capacity of existing energy storage systems of the ECAS by 1.7 times. Based on a peak-flat-valley electricity price ratio of 3.4:2:1, an optimal economic performance is attained at 100 bar liquefaction pressure, delivering a 7.21% in cost saving rate compared to conventional ASUs. The liquefaction unit’s payback period is 6.39 years—68.1% shorter than conventional LAES. This study aims to enhance both the energy storage capacity and economic performance of integrated systems combining ECAS with LAES.
2 August 2021 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
Accelerating the low-carbon transition of transport is essential to addressing global climate change. Although the rapid growth of the electric vehicle (EV) fleet highlights the environmental benefits of electrified mobility, carbon-intensive upstream electricity generation and energy-intensive battery production continue to constrain the life-cycle emissions reduction potential of EVs. Focusing on China, this structured narrative review examines 121 core references from 2004 to 2026 to synthesize carbon-accounting methods and emissions across the manufacturing, use, and end-of-life stages. A supplementary keyword co-occurrence analysis of 1180 Web of Science records provides an overview of the research field. The reviewed evidence indicates that embodied emissions from manufacturing account for more than 30% of total life-cycle emissions, making this stage important to life-cycle decarbonization. The use stage offers the greatest emissions reduction potential and is closely linked to regional grid carbon intensity and vehicle-to-grid (V2G) scheduling. At the end of life, second-life battery use and closed-loop recycling can reduce the burden associated with initial production and support material circularity. Drawing on these findings and the development of China’s EV industry, this review proposes decarbonization pathways for enterprises and policymakers to support the coordinated development of the transport and energy sectors.