The accuracy of line-of-sight (LOS)-based indoor visible light positioning (VLP) depends directly on the accuracy of the received LOS power. In an actual indoor visible light communication (VLC) system, the total received power contains the LOS power and diffuse power, and the proportion of diffuse component varies significantly with the receiving orientation of the user equipment (UE). In the trilateration positioning process, this is bound to bring a very high level of inaccuracy for at least one or two of them when determining the distance between the positioned LED and UE. To solve this problem, we employed channel estimation and Parseval’s theorem to remove the diffuse component from the total received power. The simulation results show that the higher the channel estimation accuracy, the smaller the discrepancy between the estimated and actual LOS power, and the greater the localization accuracy. At the same channel estimation accuracy, the comparison results demonstrate that the localization performance of the proposed method is higher than LLS-1, in which the total received power is directly adopted to estimate the distance. The localization performance of LLS-2 deteriorates significantly compared to the proposed method. This result indicates that the receiving orientation cannot be neglected during the distance estimation process even though the estimated accuracy of LOS power is high. Deriving the Cramér–Rao low bound (CRLB) for LOS-based indoor VLP with receiving orientation, we compared the localization performance for the proposed method with LLS-1, LLS-2, and the CRLB at various signal-to-noise ratios (SNRs). The results show that the localization error of all the received positions in the room can reach the CRLB at approximately 25 dB. However, localization errors based on LLS-1 and LLS-2 cannot achieve the theoretical CRLB even at a high SNR.

A filter-free, image-reject, sub-harmonic downconverted RoF link is proposed based on a dual-polarization quadrature phase-shift keying (DP–QPSK) modulator. At the remote antenna unit, the receiving radio frequency signal is applied to the upper QPSK modulator to achieve carrier-suppressed single-sideband (CS–SSB) modulation. The local oscillator (LO) is applied to the lower QPSK modulator, achieving sub-harmonic single-sideband (SH–SSB) modulation. The I/Q mixing is realized by exploiting a two-channel photonic microwave phase shifter, which mainly consists of a modulator, two polarization controllers, and two polarizers. The image interference signal can be rejected when combing the I and Q IF signals through a 90° electrical hybrid. Because the scheme is simple and filter-free, it has a good image-reject capability over a large frequency tunable range. Moreover, due to the special SH-SSB modulation, the modulated signals are immune to the chromatic dispersion-introduced power fading effect. Last, the sub-harmonic downconverter can decrease the frequency requirement of the LO signal. Experimental results show that an image rejection ratio (IRR) greater than 50 dB can be achieved when transmitted through a 25 km single-mode fiber (SMF). Simultaneously, under different RF signals and IF signals, the IRR has no periodic power fading, only small fluctuations. Image rejection capability of the scheme for the 50-MBaud 16-QAM wideband vector signal is also verified and the demodulation of the desired IF signal with a good EVM of less than 5% is realized.

Optimization of the light source layout is an important issue for indoor visible light communication systems, as it affects the received optical power distribution and user perception. In this paper, we propose a local optimization strategy for the light source layout that balances optimization effectiveness with optimization efficiency. First, we divide the optimization region into multiple sub-regions with different sizes and optimization priorities, where the sizes and optimization priorities of the individual sub-regions are determined based on the effect minimization principle among the sub-regions. We then calculate the pre-bias factor based on the equivalent mapping, which can compensate for the effect of the light sources in the latter optimized sub-region on the source layout optimization in the current sub-region. Finally, we search for the coordinate of a single light source for each sub-region using the variance of the squared distance between the projection of the light source on the receiving plane and the received point as a fitness function. Simulation results show that the proposed optimization strategy performs well when the vertical distance between the ceiling and the receiving plane is not less than 2.85 m.