Hossein Miri Lavasani

Dr. Hossein Miri Lavasani

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2022 in IEEE Transactions on Biomedical Circuits and Systems
Verified
Journal Article
Closed access
AHA N M Shahriyar Hossain
A N M Shahriyar Hossain
PMPedram Mohseni
Pedram Mohseni
HLHossein Miri Lavasani
Hossein Miri Lavasani
This paper provides a comprehensive overview of capacitive wireless power transfer (C-WPT) links for biomedical implants, and proposes an algorithmic approach to optimize their design for a theoretically feasible desired power transmission efficiency (PTE). Two C-WPT links, one involving external inductors for parasitic capacitance cancellation, and another without external inductors are presented. An accurate electrical model has been presented for both cases considering the finite conductivity of the body tissue and fringe fields emanated from the metallic plates. Ex-vivo experiments were conducted with beef tissue to demonstrate the viability of the model and the optimization algorithm. The analytical and simulation results show good agreement with the measurement (with real tissue) for both types of links across a wide range of operating frequency, including one with the highest reported frequency (∼14.6 MHz) among tuned links.

30 March 2021 in IEEE Transactions on Biomedical Circuits and Systems
Verified
Journal Article
Closed access
AHA N M Shahriyar Hossain
A N M Shahriyar Hossain
REReza Erfani
Reza Erfani
PMPedram Mohseni
Pedram Mohseni
HLHossein Miri Lavasani
Hossein Miri Lavasani
This paper studies the performance of a resonant capacitive wireless power transfer (C-WPT) link for biomedical implants in the presence of non-idealities. The study emphasizes on finding an accurate electrical model of a practical C-WPT link, which can be used to investigate the performance of the link under different practical/non-ideal scenarios. A sound knowledge about these non-idealities is crucial for device optimization. For the first time, a circuit model has been presented and analyzed, which is applicable to a practical C-WPT link undergoing plate mismatch, flexion, tissue contraction, and stretching. Our model considers the finite conductivity of the body tissue and fringe fields formed by capacitor plates. Analytical and HFSSTM simulation results have been presented for different non-idealities, and are in good agreement. Additionally, we show a procedure to interpolate non-ideal case results. The study shows that plate misalignment (causing reduction in parallel plate overlap area), and skin tissue contraction (while muscle grows), are the most detrimental factors to the link performance. We recorded ~32% and ~14% power transfer efficiency decrease due to these two worst case scenarios, respectively for a C-WPT link comprising of two pairs of 400 mm2 parallel plates (12 cm edge-to-edge separation) coated with 63.5 m thick Kapton layer and aligned around a 3 mm tissue at 20 MHz.

22 March 2021 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Closed access
ASAmir Hossein Masnadi Shirazi
Amir Hossein Masnadi Shirazi
HLHossein Miri Lavasani
Hossein Miri Lavasani
MSMojtaba Sharifzadeh
Mojtaba Sharifzadeh
YRYashar Rajavi
Yashar Rajavi
SMShahriar Mirabbasi
Shahriar Mirabbasi
MTMazhareddin Taghivand
Mazhareddin Taghivand
An ultralow-power direct-conversion Bluetooth-low-energy (BLE) receiver (RX) front-end that employs current-reuse and subthreshold techniques is presented. A stacked and self-biased low-noise amplifier (LNA) with active balun consumes 400 μW and achieves a noise figure (NF) of 3.2-dB and a high gain (programmable from 18 to 31 dB), meeting the system specifications over the process, supply voltage, and temperature (PVT) variations. The RX front-end has a measured integrated NF of 5.2 dB from 50 KHz to 1 MHz that corresponds to a sensitivity of -95.1 dBm. At an RX gain of 47 dB, IIP3 was measured at -19.7 dBm. The LC VCO operates at twice the carrier frequency with a tuning range of 4.55 to 5.15 GHz in an integer-N phase-locked loop (PLL). An ultralow-power CML divider is used to generate the LO I/Q. The integrated phase noise (IPN) of the LO at 2.4 GHz is 0.83° with spot phase noise of -119.9 dBc/Hz at 3 MHz frequency offset. The PLL is entirely placed inside the VCO inductor resulting in an overall die area reduction of 8%. A 6- μW automatic dc offset-calibrator avoids saturation of consecutive baseband blocks. Multiple μW-level feedback control loops are used in the design to make it robust over PVT variations. The RX front-end prototype is implemented in a 40-nm LP CMOS process and occupies a silicon area of 0.7 mm 2 .

3 April 2023 in IEEE Sensors Journal
Verified
Journal Article
Closed access
SJShuwei Ji
Shuwei Ji
PAParvin Akhkandi
Parvin Akhkandi
YQYu Qi
Yu Qi
Reza AbdolvandReza Abdolvand
Reza Abdolvand
HLHossein Miri Lavasani
Hossein Miri Lavasani
We demonstrate a highly-accurate active wireless microelectromechanical (MEMS) temperature sensor with the largest reported dynamic range (-40°C to 180°C) among active MEMS temperature sensors. The sensor uses a 27.2 MHz high quality factor (Q > 3,200) AlN-on-Si thin-film piezoelectric-on-silicon (TPoS) MEMS resonator to enable highly accurate temperature sensing, with minimum sensitivity (S), better than 0.011 °C across this wide temperature range. The wireless sensor uses an innovative frequency shift keying (FSK) 900 MHz direct up-conversion transmitter. The transmitter uses frequency multipliers for up-conversion, obviating the need for a temperature-stable frequency reference clock, thereby preserving the temperature coefficient of frequency (TCF) of the resonator, and consequently the sensitivity of the sensor. The experimental results show a very high correlation (<0.03% error) between the TCF of the MEMS oscillator and that of the transmitter output signal, demonstrating the viability of the proposed direct up-conversion technique. A detailed analysis of the Allan variance for MEMS temperature sensors which can be used to design for a given minimum sensitivity, is also presented in the paper.

30 January 2024 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
TLTso-Wei Li
Tso-Wei Li
SLSensen Li
Sensen Li
HLHossein Miri Lavasani
Hossein Miri Lavasani
HWHua Wang
Hua Wang
This article presents a $V$ -band (i.e., 47-75 GHz) differential four-way distributed-active-transformer (DAT) power amplifier (PA), which uses hybrid NMOS/PMOS for double nonlinearity cancellation to improve the linearity with minimal impact on the overall PA efficiency. Implemented in the 45-nm CMOS silicon-on-insulator (SOI) process, the proposed PA consists of three stages, pre-driver, driver, and PA stages, to deliver the desired gain at the $V$ -band. The PA stage includes both NMOS and PMOS transistors, while the driver stage adopts PMOS and the pre-driver stage uses NMOS transistors. This mixed NMOS/PMOS scheme provides a high-order nonlinearity cancellation, substantially improving the PA linearity, and optimizes its performance. An ultra-compact differential four-way series–parallel DAT-based power combiner is used to provide the optimum load (R $_{\text{opt}}$ ) to the mixed NMOS/PMOS PA. This proposed PA output matching network/power combiner only occupies one transformer footprint, resulting in a reduced chip area and design complexity. The PA achieves peak power-added-efficiency (PAE) of 35.4%, saturation power (P $_{\text{sat}}$ ) of 16.3 dBm, and AM–PM distortion $<$ 2 $^{\circ}$ (at output 1-dB compression point–13.5 dBm) in 50.4-58 GHz. The AM–PM distortion drops $<$ 0.5 $^{\circ}$ at 55 GHz. The PA exhibits an average PAE (PAE $_{\text{avg}}$ ) of 15.6% and rms error vector magnitude (EVM) $<$ $-$ 25 dB when transmitting a 64-QAM modulated signal with 9.5 dBm average output power (P $_{\text{avg}}$ ) at 0.5 GSym/s. The EVM remains better than $-$ 24 dB at 3 GSym/s with P $_{\text{avg}}$ of 8.1 dBm (PAE $_{\text{avg}}$ $=$ 9.1%). In addition, this PA is measured by 5G NR CP-OFDM 64-QAM modulation with multiple CCs. When using 1-CC FR2 400-MHz modulation, it achieves PAE $_{\text{avg}}$ of 14.5%, P $_{\text{avg}}$ of 10 dBm, EVM of $-$ 23.5 dB, and adjacent channel power ratio (ACPR) of $-$ 25.8 dBc. For 4-CC FR2 200-MHz modulation, the PA exhibits PAE $_{\text{avg}}$ of 8.1%, P $_{\text{avg}}$ of 8 dBm, EVM of $-$ 24.6 dB, and adjacent power channel ration (ACPR) of $-$ 24.6 dBc.

Verified
Journal Article
Open access
PDF file
JTJavad Tavakoli
Javad Tavakoli
HLHossein Miri Lavasani
Hossein Miri Lavasani
SSSamad Sheikhaei
Samad Sheikhaei
A low-power and low-jitter 1.2 GHz Integer-N PLL (INPLL) is designed in a 65 nm standard CMOS process. A novel high-gain sampling phase detector (PD), which takes advantage of a transconductance (Gm) cell to boost the gain, is developed to increase the phase detection gain by ~100× compared to the Phase-Frequency Detectors (PFDs) used in conventional PLLs. Using this high detection gain, the noise contribution of the PFD and Charge Pump (CP), reference clock, and dividers on the PLL output is minimized, enabling low output jitter at low power, even when using low-frequency reference clocks. To provide a sufficient frequency locking range, an auxiliary frequency-locked loop (AFLL) is embedded within the INPLL. An integrated Lock Detector (LD) helps detect the INPLL locked state and disables the AFLL to save on power consumption and minimize its impact on the INPLL jitter. The proposed INPLL layout measures 700 µm × 350 µm, consumes 350 µW, and exhibits an integrated phase noise (IPN) of −37 dBc (from 10 kHz to 10 MHz), equivalent to 2.9 ps rms jitter, while keeping the spur level 64 dBc lower, resulting in jitter figure of Merit (FoMjitter) ~−236 dB.