In different food technology unit operations, toxicity can be increased due to unwanted side reactions and is typically associated with the increased thermal energy that facilitates the latter. Authorities in food technology have not provided clear guidelines on using ultrasound (US), but they also have not prohibited its use in food processing. In this study, the source materials and ultrasound-assisted reactions reported in the literature were reviewed to investigate potential side reactions in ultrasound-assisted extraction (UAE). Industrial or pilot-scale processes published in the open literature and in industry patents were also examined. UAE is a highly effective extraction method that significantly increases extraction yields. According to the literature, there is no direct evidence of the formation of toxic compounds from natural food ingredients caused by UAE. However, experimental studies are urgently needed to assess the potential accumulation of toxic substances, especially in the case of certain plants.
22 September 2015 in Chemical Engineering & Technology
The production of carboxylic acids by partial wet oxidation of alkali lignin was studied experimentally. The factors influencing the different types of products, their yields and concentrations were investigated. Formic, acetic, succinic, oxalic, and glutaconic acid were the main identified products. Both the temperature and oxygen partial pressure are shown to have direct effects on the product yields whereas the lignin concentration has an indirect effect. At low lignin concentrations, the yield of products was relatively high. However, at higher concentrations, the yield decreased. By measuring the lignin molecular weight distributions, it is shown that this decrease is linked to repolymerization/condensation reactions of lignin fragments which compete with oxidative lignin depolymerization.
Integrating enzymatic treatment and acid hydrolysis potentially improves the economics of cellulose nanocrystal (CNC) production and demonstrates a sustainable cellulosic ethanol co-generation strategy. In this study, the effect of enzymatic treatment on filter paper and wood pulp fibers, and CNCs generated via subsequent acid hydrolysis were assessed. Characterization was performed using a pulp quality monitoring system, scanning and transmission electron microscopies, dynamic light scattering, X-ray diffraction, and thermogravimetric analysis. Enzymatic treatment partially reduced fiber length, but caused swelling, indicating simultaneous fragmentation and layer erosion. Preferential hydrolysis of less ordered cellulose by cellulases slightly improved the crystallinity index of filter paper fiber from 86% to 88%, though no change was observed for wood pulp fibre. All CNC colloids were stable with zeta potential values below −39 mV and hydrodynamic diameters ranging from 205 to 294 nm. Furthermore, the temperature for the peak rate of CNC thermal degradation was generally not affected by enzymatic treatment. These findings demonstrate that CNCs of comparable quality can be produced from an enzymatically-mediated acid hydrolysis biorefining strategy that co-generates fermentable sugars for biofuel production.
The production of carboxylic acids by partial wet oxidation of alkali lignin at elevated temperatures and pressures was studied experimentally. Two different heteropoly acids, phosphotungstic acid (H3PW12O40) and phosphomolybdic acid (H3PMo12O40), were used to catalyze the oxidation of lignin under hydrothermal conditions. Factors influencing the total yield of carboxylic acids formed during the partial oxidation of lignin were investigated. Formic, acetic and succinic acids were the major products identified. Of the two catalysts used, phosphomolybdic acid gave the most promising results, with carboxylic acid yields and lignin conversions of up to 45% and 95%, respectively.
Cellulose nanocrystals (CNCs) can be extracted from cellulosic materials through the degradation of non-crystalline cellulose domains in the feedstock via acid hydrolysis. However, the sugars released from the hydrolysis process cannot be easily recovered from the acid waste stream. In this study, cellulases were used to preferentially degrade non-crystalline domains with the objectives of recovering sugars and generating a feedstock with concentrated CNC precursors for a more efficient acid hydrolysis process. Filter paper and wood pulp substrates were enzyme-treated for 2–10 h to recover 20–40 wt % glucose. Substantial xylose yield (6–12 wt %) was generated from wood pulp. CNC yields from acid hydrolysis of cellulases-treated filter paper, and wood pulp improved by 8–18% and 58–86%, respectively, when compared with the original substrate. It was thought that CNC precursors accumulated in the cellulases-treated feedstock due to enzymatic digestion of the more accessible non-crystalline celluloses. Therefore, acid hydrolysis from enzyme-treated feedstock will require proportionally less water and reagents resulting in increased efficiency and productivity in downstream processes. This study demonstrates that an enzymatically-mediated process allows recovery of fermentable sugars and improves acid hydrolysis efficiency for CNC production.
1 January 2015 in Chemical Engineering Research and Design