Umberto Prisco

Prof. Dr. Umberto Prisco

Department of Chemical, Materials and Production Engineering, University of Napoli Federico II, piazzale Tecchio, 80, 80125 NAPOLI, Italy
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2012 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
ASAntonino Squillace
Antonino Squillace
Umberto PriscoUmberto Prisco
Umberto Prisco
SCS. Ciliberto
S. Ciliberto
Antonello AstaritaAntonello Astarita
Antonello Astarita

1 November 2002 in Integrated Computer-Aided Engineering
Verified
Journal Article
Closed access
PDF file
Umberto PriscoUmberto Prisco
Umberto Prisco
GGGiuseppe Giorleo
Giuseppe Giorleo
The paper surveys the current status of the models for representing, manipulating and analyzing dimensioning and tolerancing data behind the major computer-aided tolerancing (CAT) systems, now commercially available. The solid models and tolerance mo

30 March 2018 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
FIFilomena Impero
Filomena Impero
MDMartin Dix
Martin Dix
ASAntonino Squillace
Antonino Squillace
Umberto PriscoUmberto Prisco
Umberto Prisco
BPBiagio Palumbo
Biagio Palumbo
Flaviana TagliaferriFlaviana Tagliaferri
Flaviana Tagliaferri
This paper compares conventional and cryogenic cooling in the deep hole drilling of carbon fiber reinforced polymer (CFRP)/Ti stacks. Various parameters are taken into account to find if the use of cryogenic coolant is justified by the improvement of the final results. Both the thrust and the torque were acquired continuously during the machining operations and compared both in average and distribution. The use of a cryogenic coolant brings a reduction in thrust force and torque without any sensible drawback. Overall the results prove that cryogenic drilling is a suitable technology for CFRP/Ti stack drill.

15 August 2010 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
CBCiro Bitondo
Ciro Bitondo
Umberto PriscoUmberto Prisco
Umberto Prisco
ASAntonino Squillace
Antonino Squillace
PBPasquale Buonadonna
Pasquale Buonadonna
GDGennaro Dionoro
Gennaro Dionoro

31 October 2019 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
Umberto PriscoUmberto Prisco
Umberto Prisco
Antonello AstaritaAntonello Astarita
Antonello Astarita
Andrea El HassaninAndrea El Hassanin
Andrea El Hassanin
SFS. Franchitti
S. Franchitti
The effect of heat input rate, hatch spacing, and focus offset upon microstructure, hardness, and roughness of EBM-manufactured Ti – 6Al-4V titanium alloy was studied via a factorial experiment. It had been found that a coarser microstructure is generated for high heat input and low line offset. Increasing the heat input or conversely decreasing the line offset leads to a higher lath thickness with consequent lower hardness. The roughness of the top surfaces decreases with the increase of the heat input and the focus offset or with the decrease of the line offset. On the other side, the roughness of the side surfaces is dependent only on the heat input and it is proportional to the latter.

31 July 2013 in Science and Engineering of Composite Materials
Verified
Journal Article
Open access
Umberto PriscoUmberto Prisco
Umberto Prisco
The thermal conductivity of wood flour (WF) filled high-density polyethylene composites (wood plastic composite, WPC) is investigated experimentally as a function of filler content and temperature. Samples are prepared by compression molding process of previously blended and extruded WPC pellets, up to 50% weight content of WF. The thermal conductivity is measured by the heat flow meter technique in a temperature range from -15°C to 80°C. Experimental results show that the WPC thermal conductivity decreases with temperature and WF content, with the last effect due to the increase in porosity with the filler content, as confirmed by density measurements. Using the thermal conductivity of bare WF, the thermal conductivity of the wood material in WPC is estimated. This value successfully predicts the upper and lower bounds of the WPC thermal conductivity by means of the parallel and series conduction model of a multiphase composite material.