YAOYANG XIONG

Prof. Dr. YAOYANG XIONG


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 July 2016 in PLOS ONE
Verified
Journal Article
Open access
PDF file
NGNing Gan
Ning Gan
YXYAOYANG XIONG
YAOYANG XIONG
TJTing Jiao
Ting Jiao
Intraoral digital impressions have been stated to meet the clinical requirements for some teeth-supported restorations, though fewer evidences were proposed for larger scanning range. The aim of this study was to compare the accuracy (trueness and precision) of intraoral digital impressions for whole upper jaws, including the full dentitions and palatal soft tissues, as well as to determine the effect of different palatal vault height or arch width on accuracy of intraoral digital impressions. Thirty-two volunteers were divided into three groups according to the palatal vault height or arch width. Each volunteer received three scans with TRIOS intraoral scanner and one conventional impression of whole upper jaw. Three-dimensional (3D) images digitized from conventional gypsum casts by a laboratory scanner were chose as the reference models. All datasets were imported to a specific software program for 3D analysis by "best fit alignment" and "3D compare" process. Color-coded deviation maps showed qualitative visualization of the deviations. For the digital impressions for palatal soft tissues, trueness was (130.54±33.95)μm and precision was (55.26±11.21)μm. For the digital impressions for upper full dentitions, trueness was (80.01±17.78)μm and precision was (59.52±11.29)μm. Larger deviations were found between intraoral digital impressions and conventional impressions in the areas of palatal soft tissues than that in the areas of full dentitions (p0.05), but arch width was found to have a significant effect on precision of intraoral digital impressions for full dentitions (p = 0.016). A linear correlation was found between arch width and precision of digital impressions for whole upper jaws (r = 0.326, p = 0.034 for palatal soft tissues and r = 0.485, p = 0.002 for full dentitions). It was feasible to use the intraoral scanner to obtain digital impressions for whole upper jaws. Wider dental arch contributed to lower precision of an intraoral digital impression. It should be confirmed in further studies that whether accuracy of digital impressions for whole upper jaws is clinically acceptable.

1 July 2021 in Annals of Translational Medicine
Verified
Journal Article
Open access
PDF file
HWHaiyan Wang
Haiyan Wang
JXJing Xuan
Jing Xuan
LLLijun Liu
Lijun Liu
XSXuemin Shen
Xuemin Shen
YXYAOYANG XIONG
YAOYANG XIONG
Problem-based learning and case-based learning in dental education Haiyan Wang, Jing Xuan, Lijun Liu, Xuemin Shen, Yaoyang Xiong

11 January 2018 in Scientific Reports
Verified
Journal Article
Open access
PDF file
NGNing Gan
Ning Gan
YRYaye Ruan
Yaye Ruan
JSJian Sun
Jian Sun
YXYAOYANG XIONG
YAOYANG XIONG
TJTing Jiao
Ting Jiao
The objective was to compare the adaptation between the major connectors of removable partial dentures derived from intraoral digital impressions and extraoral digital impressions. Twenty-four volunteers were enrolled. Each volunteer received an intraoral digital impression and one extraoral digital impression digitized from conventional gypsum impression. A software was used to create the major connectors on digital impression datasets. After all the virtual major connectors designed from Group intraoral digital impressions (Group I) and Group extraoral digital impressions (Group E) were directly fabricated by 3D printing technique, the adaptation of the final major connectors in volunteers’ mouths were measured. The adaptation ranged from 159.87 to 577.99 μm in Group I while from 120.83 to 536.17 μm in Group E. The adaptation of major connectors in Group I were found better at the midline palatine suture while the adaptation of major connectors in Group E were found better at the two sides of the palatal vault. In both groups, the highest accuracy in adaptation was revealed at the anterior margin of the major connectors. It is feasible to manufacture the major connectors by digital impression and 3D printing technique. Both the adaptation of the two kinds of digital impressions were clinical acceptable.

24 May 2019 in Journal of Clinical Periodontology
Verified
Journal Article
Closed access
PDF file
JSJun-Yu Shi
Jun-Yu Shi
YLYuan Li
Yuan Li
SQShi‐Chong Qiao
Shi‐Chong Qiao
YGYing‐Xin Gu
Ying‐Xin Gu
YXYAOYANG XIONG
YAOYANG XIONG
HLHong-Chang Lai
Hong-Chang Lai

27 January 2025 in Journal of Dentistry
Verified
Journal Article
Closed access
NGNing Gan
Ning Gan
MYMengxin Yao
Mengxin Yao
YRYaye Ruan
Yaye Ruan
CWChengyi Wang
Chengyi Wang
YXYAOYANG XIONG
YAOYANG XIONG
TJTing Jiao
Ting Jiao

21 January 2025 in International Journal of Bioprinting
Verified
Journal Article
Open access
PDF file
JLJunlong Liu
Junlong Liu
WWWeiqu Wang
Weiqu Wang
YZYuanli Zheng
Yuanli Zheng
ZZZhe Zhao
Zhe Zhao
YXYAOYANG XIONG
YAOYANG XIONG
Digital Light Processing (DLP) 3D printing technology exhibits remarkable potential in dental manufacturing due to its exceptional precision, customization capabilities, and rapid prototyping abilities. Compared to crown and bridge restorations produced through milling and sintering, resin restorations fabricated using DLP printing technology offer higher accuracy and more efficient and economical processing methods. However, the clinical application of DLP-printed tooth crowns and bridge prostheses is limited by their poor mechanical properties and biocompatibility. In this study, a light-curing resin matrix was formulated using Urethane dimethacrylate (UDMA), Poly(propylene glycol) dimethacrylate (PPGDMA), and a novel photoinitiator 2,4,6-trimethylbenzoyl bis(p-tolyl) phosphine oxide (TMO). Silane-modified nano-silica (SiO2) was used as a reinforcing filler to achieve different solid contents in the resin matrix. Four groups of DLP-printed dental nanocomposite resins (DNRs) were prepared with varying solid contents: 16%wt, 19%wt, 22%wt, and 25%wt. Subsequently, comprehensive evaluations were conducted on the rheological properties, flexural strength, compressive strength, hardness, water absorption capacity, solubility, double bond conversion efficiency, and light transmittance of DNRs with different solid contents. The aesthetic properties and the biocompatibility of DNRs were further assessed using gingival fibroblasts. The results demonstrated that incorporating 19% wt SiO2 nanoparticles into the resin matrix significantly enhanced both physical-mechanical properties and biocompatibility of DNRs. In conclusion, the DLP-printed dental nanocomposite with a solid content of 19%wt exhibited excellent physical-mechanical properties and biocompatibility, suggesting its potential for application in crown and bridge restorations for DLP-printed teeth.