Easy and cost-efficient modifications of titanium dioxide nanoparticles that improve their efficiency in the visible light domain represent a continuous and challenging research topic. In addition, the effect of graphene on the overall photocatalytic process is still debated. Consequently, herein, we prepared a series of TiO₂ nanoparticle-based composites with different copper oxide mass content (1–3%) and co-doped with graphene of different oxidation degrees. Different characterization techniques were used to analyze the structural and physico-chemical properties of the obtained composites: Scanning Electron Microscopy (SEM)/Transmission Electron Microscopy (TEM)/Energy-dispersive X-ray spectroscopy (EDX) analysis, X-ray powder diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The photocatalytic performance was evaluated by the degradation of methylene blue under both UVA and visible light irradiation. The nanocomposites show very good photocatalytic activity independent of the presence of reduced graphene oxide, due to the Cu₂O/CuO-TiO₂ heterojunctions. This finding has been confirmed by the very efficient visible-light-driven degradation of amoxicillin and ciprofloxacin.

The properties of newly synthesized Cu₂O/CuO-decorated TiO₂/graphene oxide (GO) nanocomposites (NC) were analyzed aiming to obtain insight into their photocatalytic behavior and their various applications, including water remediation, self-cleaning surfaces, antibacterial materials, and electrochemical sensors. The physico-chemical methods of research were photoluminescence (PL), electron paramagnetic resonance (EPR) spectroscopy, cyclic voltammetry (CV), and differential pulse voltammetry (DPV). The solid samples evidenced an EPR signal that can be attributed to the oxygen-vacancy defects and copper ions in correlation with PL results. Free radicals generated before and after UV-Vis irradiation of powders and aqueous dispersions of Cu₂O/CuO-decorated TiO₂/GO nanocomposites were studied by EPR spectroscopy using two spin traps, DMPO (5,5-dimethyl-1-pyrroline-N-oxide) and CPH (1-hydroxy-3-carboxy-2,2,5,5-tetramethylpyrrolidine), to highlight the formation of hydroxyl and superoxide reactive oxygen species, respectively. The electrochemical characterization of the NC modified carbon-paste electrodes (CPE) was carried out by CV and DPV. As such, modified carbon-paste electrodes were prepared by mixing carbon paste with copper oxides-decorated TiO₂/GO nanocomposites. We have shown that GO reduces the recombination process in TiO₂ by immediate electron transfer from excited TiO₂ to GO sheets. The results suggest that differences in the PL, respectively, EPR data and electrochemical behavior, are due to the different copper oxides and GO content, presenting new perspectives of materials functionalization.

A novel nanoporous adsorbent was obtained through the thermal treatment and chemical wash of the wasted crab shells (BC1) and characterized by various techniques. The structure of BC1 at the end of the treatments comprised a mixture of calcite and amorphous CaCO₃, as evidenced by X-ray diffraction and Fourier transform infrared absorption. The BET surface area, BET pore volume, and pore diameter were 250.33 m² g⁻¹, 0.4 cm³ g⁻¹, and <70 nm, respectively. The point of zero charge of BC1 was determined to be around pH 9. The prepared adsorbent was tested for its adsorption efficacy towards the neonicotinoid pesticide acetamiprid. The influence of pH (2–10), temperature (20–45 °C), adsorbent dose (0.2–1.2 g L⁻¹), contact time (5–60 min), and initial pesticide concentration (10–60 mg L⁻¹) on the adsorption process of acetamiprid on BC1 was studied. The adsorption capacity of BC1 was 17.8 mg g⁻¹ under optimum conditions (i.e., 20 mg L⁻¹ initial acetamiprid concentration, pH 8, 1 g L⁻¹ adsorbent dose, 25 °C, and 15 min contact time). The equilibrium data obtained from the adsorption experiment fitted well with the Langmuir isotherm model. We developed an effective nanoporous adsorbent for the recycling of crab shells which can be applied on site with minimal laboratory infrastructure according to local needs.

Surface modification of textile fabrics and leathers is very versatile and allows the products quality improvement. In this work, cotton and leather substrates were pre-treated with cold atmospheric pressure plasma (CAPP) and further coated with TiO₂-SiO₂-reduced graphene oxide composites in dispersion form. By using a Taguchi scheme, this research evaluated the effect of three significant parameters, i.e., the pre-treatment with CAPP, organic dispersion coating and TiO₂-SiO₂-reduced graphene oxide (TS/GR) composites, that may affect the morpho-structural properties and photocatalytic activity of modified cotton and leather surfaces. The characteristics of cotton/leather surfaces were evaluated by morphological, structural, optical and self-cleaning ability using scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), X-ray powder diffraction (XRD), attenuated total reflection–Fourier Transform Infrared spectroscopy (ATR-FTIR) and UV–Vis spectroscopy. The self-cleaning performance of the obtained cotton and leather samples was evaluated by photocatalytic discoloration of berry juice surface stains under UV light irradiation for 12 h. The successfulness of coating formulations was proven by the SEM analysis and UV–Vis spectroscopy. The XRD patterns and ATR-FTIR spectra revealed the cellulose and collagen structures as dominant components of cotton and leather substrates. The CAPP treatment did not damage the cotton and leather structures. The photocatalytic results highlighted the potential of TiO₂-SiO₂-reduced graphene oxide composites in organic dispersion media, as coating formulations, for further use in the fabrication of innovative self-cleaning photocatalytic cotton and leather products.

The degradation of amoxicillin was accomplished using TiO2 nanotubes photocatalysts decorated with Au nanoparticles and containing reduced graphene or nitrogen-doped graphene under visible light exposure. The structural and morphological characterization confirmed the presence of gold nanoparticles and graphene, and the optical properties showed light absorption into visible region. The best results in the degradation of amoxicillin (up to 60%) were reached in the presence of the photocatalyst with nitrogen-doped graphene. A basics kinetic study showed a physical adsorption of the amoxicillin on the catalyst surface, and that the photodegradation step followed the pseudo-first kinetic model with the apparent kinetic constant of 0.0039 min-1.