Cracks in oil and gas pipelines cause leakage which results in property damage, environmental pollution, and even personal injury or loss of lives. In this paper, an active-sensing approach was conducted to identify the crack damage in pipeline structure using a stress wave propagation approach with piezoceramic transducers. A pipeline segment instrumented with five distributed piezoceramic transducers was used as the testing specimen in this research. Four cracks were artificially cut on the specimen, and each crack had six damage cases corresponding to different crack depths. In this way, cracks at different locations with different damage degrees were simulated. In each damage case, one piezoceramic transducer was used as an actuator to generate a stress wave to propagate along the pipeline specimen, and the other piezoceramic transducers were used as sensors to detect the wave responses. To quantitatively evaluate the crack damage status, a wavelet packet-based damage index matrix was developed. Experimental results show that the proposed method can evaluate the crack severity and estimate the crack location in the pipeline structure based on the proposed damage index matrix. The sensitivity of the proposed method decreases with increasing distance between the crack and the mounted piezoceramic transducers.

Impact loads can have major adverse effects on the safety of civil engineering structures, such as concrete-filled steel tubular (CFST) columns. The study of mechanical behavior and stress analysis of CFST columns under impact loads is very important to ensure their safety against such loads. At present, the internal stress monitoring of the concrete cores CFST columns under impact loads is still a very challenging subject. In this paper, a PVDF (Polyvinylidene Fluoride) piezoelectric smart sensor was developed and successfully applied to the monitoring of the internal stress of the concrete core of a CFST column under impact loads. The smart sensor consists of a PVDF piezoelectric film sandwiched between two thin steel plates through epoxy. The protection not only prevents the PVDF film from impact damages but also ensures insulation and waterproofing. The smart sensors were embedded into the circular concrete-filled steel tube specimen during concrete pouring. The specimen was tested against impact loads, and testing data were collected. The time history of the stress obtained from the PVDF smart sensor revealed the evolution of core concrete internal stress under impact loads when compared with the impact force–time curve of the hammer. Nonlinear finite element simulations of the impact process were also carried out. The results of FEM simulations had good agreement with the test results. The results showed that the proposed PVDF piezoelectric smart sensors can effectively monitor the internal stress of concrete-filled steel tubular columns under impact loads.

L-shaped concrete filled steel tube (L-CFST) columns are used frequently in civil engineering, and the concrete damage inside the L-CFST column is difficult to monitor. This research aims to develop a new method to monitor the internal concrete damage in the L-CFST column by using embedded piezoceramic smart aggregates (SAs) under low frequency cyclic loading. The SA enabled active method is used to monitor the concrete damages near the bottom of the L-CFST columns, and the wavelet packet analysis is used to establish a damage index, which is used to analyze the acquired data. During the experiment, three L-CFST columns with different wall thickness of the steel tube were tested. The experimental results find that the structural damage indices under the low-frequency cyclic loading are basically consistent with the results of the hysteretic curves and the skeleton curve of the specimens, and are in good agreement with the experimental phenomena. We conclude that the use of smart aggregate can directly and clearly reflect the damage process of the concrete core, demonstrating the feasibility of using piezoceramic smart aggregates to monitor the internal concrete damage of the L-CFST column.

Concrete-filled square steel tube column (CFSSTC) joints are the most important parts of concrete-filled steel tube frame structures. It is of great significance to study the damage of CFSSTC joints under the seismic loads. In this paper, embedded piezoceramic transducers are used to monitor the damage of core concrete of CFSSTC joints under cyclic loading and surface-bonded piezoceramic disks are used to monitor the debonding damage of the steel tube and core concrete of two specimens. The damages of the joints under different loading levels and different loading cycles are evaluated by the received signal of the piezoceramic transducers. The experimental results show that the amplitude of the signal attenuates obviously with the appearance of damage in the joints, and the degree of attenuation increases with the development of the damage. The monitoring results from piezoceramic transducers are basically consistent with the hysteresis loops and skeleton curves of the CFSSTC joints during the cyclic loading. The effectiveness of the piezoceramic transducers are verified by the experimental results in structural health monitoring of the CFSSTC joint under cyclic loading.

The filling of thin-walled steel tubes with quartz sand can help to prevent the premature buckling of the steel tube at a low cost. During an impact, the internal stress of the quartz sand-filled steel tube column is subjected to not only axial force but also lateral confining force, resulting in complicated internal stress. A suitable sensor for monitoring the internal stress of such a structure under an impact is important for structural health monitoring. In this paper, piezoceramic Smart Aggregates (SAs) are embedded into a quartz Sand-Filled Steel Tube Column (SFSTC) to monitor the internal structural stress during impacts. The piezoceramic smart aggregates are first calibrated by an impact hammer. Tests are conducted to study the feasibility of monitoring the internal stress of a structure. The results reflect that the calibration value of the piezoceramic smart aggregate sensitivity test is in good agreement with the theoretical value, and the output voltage value of the piezoceramic smart aggregate has a good linear relationship with external forces. Impact tests are conducted on the sand-filled steel tube with embedded piezoceramic smart aggregates. By analyzing the output signal of the piezoceramic smart aggregates, the internal stress state of the structure can be obtained. Experimental results demonstrated that, under the action of impact loads, the piezoceramic smart aggregates monitor the compressive stress at different locations in the steel tube, which verifies the feasibility of using piezoceramic smart aggregate to monitor the internal stress of a structure.

The purpose of this research is to study the effect of both transverse impact, and ratio of outer diameter to thickness of outer steel tube (D/t), on the residual axial bearing capacity of concrete-filled circular steel tubular columns (CFCSTCs). A total of sixteen samples, including four samples left untreated for comparison, are experimentally studied to investigate the effect of both drop-hammer transverse impact height (H), and D/t ratio, on the residual axial bearing capacity of CFCSTCs. The failure mode, load-displacement curves, load-strain curves, and residual axial bearing capacity of those samples are extensively investigated. A finite element analysis (FEA) model is established to predict the effect of D/t ratio on the residual axial bearing capacity of CFCSTCs. The results indicate that the H and the D/t ratio have noticeable effects on the axial compression performance of CFCSTCs. Failure mode of samples is commonly local buckling. In addition, maximum reduction of the axial bearing capacity of columns reaches about 35% compared with that of untreated columns. The results also show that the bearing capacity of the column increases with a decreasing D/t ratio of the same diameter (D).