Na 3 V 2 (PO 4 ) 2 F 3 is an ideal cathode material for sodium-ion batteries with a high theoretical energy density. In this paper, the electronic conductivity of Na 3 V 2 (PO 4 ) 2 F 3 was improved by using a simple surface carbon coating method, and excellent electrochemical properties were obtained.
In this study, the W (10–20%)–Cu composites were simultaneously fabricated using commercial, graded commercial, and graded jet-milled W powder. The results show that the W–Cu composites prepared with the graded jet-milled W powders have the highest density and best comprehensive performance due to the combined effect of the particle gradation and jet-milling treatment. Particle gradation is employed to increase the packing density of powders, thereby increasing the relative density of the compressed W skeleton, and the rounded powder with narrow particle size distribution after jet-milling treatment is used to reduce the enclosed pores formed during the process of compacting and infiltration. W–Cu composites with a high density of 16.25 g/cm3 can be directly obtained by conventional compacting at a low pressure of 300 MPa and following infiltration.
To address the issue of over-standard short-circuit currents in a power system, it is imperative to enhance the comprehensive performance of the electrical contacts, which serve as the lynchpin of circuit breakers, so as to improve the breaking capacity of high-voltage circuit breakers. Graphene, as the most prominent two-dimensional carbon material in recent years, has garnered widespread applications across various fields. In this study, graphene-enhanced CuW composites for high-voltage circuit breaker electrical contacts were prepared innovatively using integrated vacuum infiltration technology. The innovative graphene-enhanced CuW composites significantly improved the mechanical, electrical, and ablation resistance properties, and have been successfully applied in the 252 kV/63 kA high-voltage SF6 circuit breakers, achieving 20 times effective consecutive full-capacity short-circuit current breaking. It provides a new route for the development and application of high-performance CuW electrical contacts. Looking ahead, it is planned to extend their application to higher voltage grade high-voltage circuit breakers.
Copper powder has broad applications in the powder metallurgy, heat exchanger, and electronic industries due to its intrinsically high electrical and thermal conductivities. However, the ease of formation of surface oxide or patina layer raises difficulty of storage and handling of copper powder, particularly in the case of Cu microparticles. Here, we developed a thermal chemical vapor deposition chemical vapor deposition (CVD) process for large-scale synthesis of graphene coatings on Cu microparticles, which importantly can remain monodisperse without aggregation after graphene growth at high temperature by using removal spacers. Compared to other protective coating methods, the intrinsic electrical and thermal properties of Cu powder would not be degraded by uniform growth of low defect few-layer graphene on each particle surface. As a result, when the anticorrosion performance test was carried out by immersing the samples in Cu etchant, the corrosion rate of graphene/Cu microparticles was significantly improved (ca three times slower) compared to that of pristine Cu powder, also showing a comparable anticorrosion ability to commercial CuZn30 alloy.
Copper–tungsten (Cu-W) composites are widely used in high-power and -temperature electrical applications. The combination of these metals, however, leads to compromised physical and electrical properties. Herein, we produce Cu-W-graphene oxide (Cu-W-GO) composites to address this challenge. To ensure uniform density composites, the as-received metal powders were flattened into a flake morphology by ball milling and then mixed with up to 0.5 wt.% GO flakes. The green forms were processed using spark plasma sintering. The GO was found to be well-dispersed amongst the metallic phases in the final composite. The addition of GO reduced the relative density of the composites slightly (4.7% decrease in relative density at 0.5 wt% GO loading for the composites processed at 1000 °C). X-ray diffraction confirmed good phase purity and that no carbide phases were produced. GO was found to improve the mechanical properties of the Cu-W, with an optimal loading of 0.1 wt.% GO found for ultimate compression strength and strain to failure, and 0.3 wt.% optimal loading for the 0.2% offset yield strength. Significantly, the electrical conductivity increased by up to 25% with the addition of 0.1 wt.% GO but decreased with higher GO loadings.
The global phase-out of sulfur hexafluoride (SF6), an insulating gas with high global warming potential (GWP), has driven the search for eco-friendly alternatives in high-voltage equipment. Perfluoroisobutyronitrile (C4F7N) emerges as a promising candidate due to its low GWP and high dielectric strength. However, its chemical stability under circuit breaker conditions, especially when interacting with vaporized contact materials such as silver, remains a key concern. This study investigates the decomposition mechanisms of C4F7N in the presence of silver vapor using quantum chemical calculations at the B3LYP/LanL2DZ level. A reaction network comprising 35 pathways and 12 transition states were identified. All structures were confirmed as valid stationary points via frequency analysis and intrinsic reaction coordinate (IRC) calculations. Three primary reaction pathways between C4F7N and Ag were delineated, leading to secondary reactions that generate low-weight molecules and Ag-containing species such as AgF and AgCN. Key energy barriers and temperature-dependent equilibrium constants (Keq) were determined to evaluate pathway feasibility. This work provides fundamental insights into the high-temperature interfacial chemistry of C4F7N with Ag, offering essential data for assessing its material compatibility and long-term reliability as a sustainable insulation medium in power systems.