Jungju Lee

Dr. Jungju Lee

orcid

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2018 in Tribology International
Verified
Journal Article
Closed access
JLJungju Lee
Jungju Lee
JLJung-A. Lee
Jung-A. Lee
SKSungwook Kwon
Sungwook Kwon
JKJeong-Joo Kim
Jeong-Joo Kim

1 February 2021 in Wear
Verified
Journal Article
Closed access
JPJongsung Park
Jongsung Park
BJByungsoo Joo
Byungsoo Joo
HSHyungjo Seo
Hyungjo Seo
WSWansu Song
Wansu Song
JLJungju Lee
Jungju Lee
HJHo Jang
Ho Jang

1 February 2021 in Tribology International
Verified
Journal Article
Closed access
HSHyungjo Seo
Hyungjo Seo
BJByungsoo Joo
Byungsoo Joo
JPJongsung Park
Jongsung Park
YKYun Cheol Kim
Yun Cheol Kim
JLJungju Lee
Jungju Lee
HJHo Jang
Ho Jang

1 January 2013 in Review of Scientific Instruments
Verified
Journal Article
Closed access
YYYoung Ik Yoo
Young Ik Yoo
JJJu Won Jeong
Ju Won Jeong
Jae Hyuk LimJae Hyuk Lim
Jae Hyuk Lim
KKKyung Won Kim
Kyung Won Kim
DHDo-Soon Hwang
Do-Soon Hwang
JLJungju Lee
Jungju Lee
We have developed a newly designed non-explosive release actuator that can replace currently used release devices. The release mechanism is based on a separation mechanism, which relies on segmented nuts and a shape memory alloy (SMA) wire trigger. A quite fast and simple trigger operation is made possible through the use of SMA wire. This actuator is designed to allow a high preload with low levels of shock for the solar arrays of medium-size satellites. After actuation, the proposed device can be easily and instantly reset. Neither replacement, nor refurbishment of any components is necessary. According to the results of a performance test, the release time, preload capacity, and maximum shock level are 50 ms, 15 kN, and 350 G, respectively. In order to increase the reliability of the actuator, more than ten sets of performance tests are conducted. In addition, the proposed release actuator is tested under thermal vacuum and extreme vibration environments. No degradation or damage was observed during the two environment tests, and the release actuator was able to operate successfully. Considering the test results as a whole, we conclude that the proposed non-explosive release actuator can be applied reliably to intermediate-size satellites to replace existing release systems.

1 January 2012 in IERI Procedia
Verified
Journal Article
Open access
JJJu Won Jeong
Ju Won Jeong
YYYoung Ik Yoo
Young Ik Yoo
JLJungju Lee
Jungju Lee
Jae Hyuk LimJae Hyuk Lim
Jae Hyuk Lim
KKKyung Won Kim
Kyung Won Kim
This paper presents a novel hinge mechanism for deployment of spacecraft subsystems such as antennas, solar arrays. By using Axiomatic design theory, the conceptual design of the hinge mechanism is suggested, which has not only high deployed stiffness and low deployment shock but also does not require lubrication and accurate fabrication. That is, optimization of deployment torque and maximization of the deployed stiffness can be possible since this suggested hinge mechanism is decoupled design. And the suggested hinge mechanism is fabricated and tested to evaluate the feasibility. Quasi-static analysis is performed to optimize deployment torque for low deployment shock by using FEM. Also, the bending stiffness is measured by 4 point bending test

18 September 2011 in SAE International Journal of Materials and Manufacturing
Verified
Journal Article
Closed access
PDF file
SKSeong Jin Kim
Seong Jin Kim
JLJae Young Lee
Jae Young Lee
JHJai Min Han
Jai Min Han
YKYoon Cheol Kim
Yoon Cheol Kim
HPHyun Dal Park
Hyun Dal Park
HJHo Jang
Ho Jang
Copper has been regarded as one of the indispensable ingredients in the brake friction materials since it provides high thermal diffusivity at the sliding interface. However, the recent regulations against environmentally hazardous ingredients limit the use of copper in the commercial friction material and much effort has been made for the alternatives. In this work, the role of the cuprous ingredients such as copper fiber, copper powder, cupric oxide (CuO), and copper sulfide (CuS) are studied using the friction materials based on commercial formulations. The investigation was performed using a full inertial brake dynamometer and 1/5 scale dynamometer for brake performance and wear test. Results showed that the cuprous ingredients played a crucial role in maintaining the stable friction film at the friction interface, resulting in improved friction stability and reduced aggressiveness against counter disk. In particular, the addition of copper fiber or copper sulfide contributed to improved friction stability during effectiveness test. The test result also showed that the friction material containing 10 wt.% of cupric oxide exhibited better fade resistance without showing an abrupt decrease of friction coefficient during brake performance and wear tests. The addition of copper fiber showed better wear resistance compared to the friction material with cupric oxide, on the other hand, the increase of copper fiber showed an adverse effect in the wear resistance of the friction materials during wear tests up to 400°C.