Original Article Multimodal therapy of epithelioid pleural mesothelioma: improved survival by changing the surgical treatment approach Laura V. Klotz, Hans Hoffmann, Rajiv Shah, Florian Eichhorn, Christiane Gruenewald, Elena L. Bulut, Raffaella Griffo, Thomas Muley, Petros Christopoulos, Philip Baum, Peter Huber, Seyer Safi, Marc Kriegsmann, Michael Thomas, Helge Bischoff, Hauke Winter, Martin E. Eichhorn
Wettability, typically estimated through the contact angle, is a fundamental property of surfaces with wide-ranging implications in both daily life and industrial processes. Recent scientific interest has been paid to the surfaces exhibiting extreme wettability: superhydrophobic and superhydrophilic surfaces, characterized by high water repellency and exceptional water wetting, respectively. Both chemical composition and morphology play a role in the determination of the wettability “performance” of a surface. To tune surface-wetting properties, we considered coatings of carbon nanoparticles (CNPs) in this study. They are a new class of nanomaterials synthesized in flames whose chemistry, dimension, and shape depend on combustion conditions. For the first time, we systematically studied the wettability of CNP coatings produced in a controlled rich ethylene/air flame stabilized over a McKenna burner. A selected substrate was intermittently inserted in the flame at 15 mm above the burner to form a thin coating thanks to a thermophoretic-driven deposition mechanism. The chemical-physical quality and the deposed quantity of the CNPs were varied by opportunely combing the substrate flame insertion number (from 1 to 256) and the carbon-to-oxygen ratio, C/O (from 0.67 to 0.87). The wettability of the coatings was evaluated by measuring the contact angle, CA, with the sessile drop method. When the C/O = 0.67, the CNPs were nearly spherical, smaller than 8 nm, and always generated hydrophilic coatings (CA < 35°). At higher C/O ratios, the CNPs reached dimensions of 100 nm, and fractal shape aggregates were formed. In this case, either hydrophilic (CA < 76°) or superhydrophobic (CA ~166°) behavior was observed, depending on the number of carbon nanoparticles deposed, i.e., film thickness. It is known that wettability is susceptible to liquid surface tension, and therefore, tests were conducted with different fluids to establish a correlation between the flame conditions and the nanostructure of the film. This method offers a fast and simple approach to determining mesoscale information for coating roughness and topographical homogeneity/inhomogeneity of their surfaces.
Fog formation and moisture condensation limit the performance of glass surfaces in optical, microfluidic, and sensing applications, where stable transparency under humid conditions is essential. Enhancing surface wettability represents an effective strategy to mitigate these effects; therefore, the development of methods to tailor glass wettability is of scientific and technological relevance. In this context, the present study investigates a controlled flame treatment of glass surfaces to enhance their hydrophilicity, with the extent and short‐ and long‐term stability depending on processing conditions. In particular, an in‐flame treatment is investigated, in which microscope glass slides are exposed to a premixed lean ethylene/air flame (equivalence ratio, Φ = 0.78) generated by a McKenna burner. The chemically active flame environment, rich in oxidizing radicals such as O and OH and in combustion products including H 2 O, enables rapid surface activation. Different exposure regimes are systematically compared, including short intermittent flame insertions and continuous exposure, to clarify the role of temporal continuity in the activation process. Static water contact angle measurements reveal a decrease from 42.36 ± 3.93° for pristine glass to approximately 12° after treatment, demonstrating a shift toward hydrophilicity. Additional stability assessments based on repeated mild cleaning cycles indicate that the persistence of the induced hydrophilicity depends on the flame exposure modality. Overall, these results demonstrate that flame treatment can serve as a rapid, scalable, and efficient route for glass surface activation, offering an alternative to plasma‐based techniques or prolonged thermal treatments for antifogging and related optical applications.
Carbon‐based films are widely used in technologies requiring surfaces with controlled wettability. These films can be synthesized by depositing carbon nanoparticles (CNPs) onto substrates intermittently inserted into rich premixed flames, where thermophoresis drives particle capture. Depending on flame conditions, this method yields either hydrophilic films (from incipient sooting flames) or superhydrophobic films (from fully sooting flames). However, under incipient sooting conditions, the low concentration and small size of CNPs result in slow deposition, limiting practical applications. This study explores Electric Field‐Assisted Thermophoretic Flame Synthesis (E‐ThFS) as a strategy to enhance deposition. Rich ethylene/air flames are used, and the effect of an external electric field is investigated. UV–vis spectroscopy, profilometry, and contact angle measurements show that applying a −3 kV electric field accelerates deposition up to fivefold and alters surface morphology, producing more heterogeneous textures. The hydrophilic character of films from incipient sooting flames is preserved, although it may be preceded by a brief metastable superhydrophobic state whose duration decreases as voltage increases. In fully sooting flames, the electric field similarly enhances deposition and roughness while maintaining superhydrophobicity. These findings demonstrate the potential of E‐ThFS as a scalable, one‐step method for creating carbon coatings with tunable wettability and morphology.
Polymer particles have a wide range of applications from medicine to electronics. Among the several production methods, the emulsion solvent evaporation technique is widely used due to its simplicity and reproducibility. In this process, the selection of operating conditions is fundamental for generating products with dimensions suitable for specific applications. Therefore, predictive models play a key role in production process optimizing, minimizing the number of experiments required to identify optimal conditions. In this context, the proposed study presents a novel predictive model for estimating the Sauter mean diameter of emulsion droplets and polymeric particles. The emulsions were prepared using a rotor-stator emulsifier, and the polymeric particles were produced through the emulsion solvent evaporation technique. Commonly used polymers, such as polycaprolactone at different molecular weights and polylactic acid, and solvents, such as chloroform and dichloromethane, were selected for particle production. The obtained dataset was then used to develop a new robust and accurate model based on the Buckingham Π-theorem. From the results, the root mean square errors obtained from the models were found to be between 12% and 21%, thus highlighting the accuracy of the proposed models. A comparison of the models obtained in this study with those found in the existing literature reveals that the proposed models exhibit the lowest errors. Therefore, the used methodology allowed to develop an accurate predictive model for droplets and particles. This approach addresses a significant gap in the literature, as predictive models for particles are currently lacking.