Intensive and massive coal mining causes a series of geological hazards and environmental problems, especially surface subsidence. At present, two major types of subsidence control technology are applied: backfilling technology and partial mining technology. However, the cost of backfill mining is high and partial mining has a low recovery ratio. Therefore, the backfill‐strip mining is used to solve the problems of high cost and shortage of filling materials in coal mines at present. A subsidence control design method of backfill‐strip mining was proposed in this paper based on the subsidence control effects and economic benefits. First, the stability of the composite support pillar of the filling body and coal pillars in the backfill‐strip mining is analyzed, and the values of the main subsidence influencing factors that include the filling material, the size of the backfilling working face, caving mining face, and residual coal pillar are preliminarily determined. Then, the surface movement and deformation are predicted based on the equivalent superposition probability integral method (PIM). The subsidence influencing factors are optimized and determined by comparing the requirements of the safety fortification index of the antideformation ability of surface buildings, resource recovery rate, and coal mining cost. Finally, the mining scheme design parameters of the backfill‐strip mining technology are determined. This method is applied in the subsidence control design of backfill‐strip mining in the Ezhuang coal mine. Research results show that backfill‐strip mining can ensure the safety of surface buildings, increase the resource recovery rate, and reduce coal mining costs through the reasonable design of this method. This study can provide scientific guidance for subsidence disaster control, prevention, and engineering design in backfill‐strip mining.
Surface waterlogging disasters due to underground mining and geological status have caused the abandonment of fertile land, seriously damaged the ecological environment, and have influenced the sustainable development of coal resource-based cities, which has become a problem that some mining areas need to face. However, the traditional underwater terrain measurement method using sonar encompasses a time-consuming and labor-intensive process. Thus, an inversion method for obtaining the underwater spatial information of subsidence waterlogging in coal mining subsidence waterlogging areas is proposed, based on differential interferometric synthetic aperture radar (D-InSAR) and the probability integral prediction method. First, subsidence values are obtained in the marginal area of the subsidence basin using D-InSAR technology. Then, the subsidence prediction parameters of the probability integral method (PIM) are inverted by a genetic algorithm (GA) based on the subsidence values. Finally, the underwater spatial information of subsidence waterlogging is calculated on the basis of the prediction parameters. The subsidence waterlogging area in the Wugou coal mine was adopted as the study area, and the underwater spatial information of subsidence waterlogging was inverted by the proposed method. The results show that this method can effectively provide the underwater spatial information of subsidence waterlogging, including the maximum subsidence value, waterlogging volume, subsidence waterlogging area, and underwater terrain in the subsidence waterlogging area. Compared with field-measured data from the same period, the RMSE of water depth is 99 mm, and the relative error is 9.9%, which proves that this inversion method is accurate and can meet engineering precision requirements.
Ensuring shaft safety is crucial for underground coal mining. The prevailing method for monitoring shaft deformation involves manual measurements conducted regularly, necessitating numerous surveyors to descend into the shaft. This approach is laborious and time-consuming, and its reliance on human intervention significantly affects accuracy. An emerging alternative employs an enhanced laser slam scanner comprising laser ranging and inertial navigation angle measurement modules. The accuracy of the inertial navigation angle often requires refinement through laser point cloud registration to mitigate errors. However, existing research has not explored the utilization of a single inertial navigation sensor within a shaft, which potentially influences measurement outcomes. To investigate the impact of inertial navigation angle measurement errors from lidar scanners on shaft interior measurements and propose corresponding error reduction methods, this study developed a multisensor fusion system for monitoring shaft wall deformations. Three experiments were conducted to assess the accuracy of this monitoring system: a laboratory experiment, a simulated experiment, and a real shaft experiment. The results demonstrated that the maximum mean absolute errors (MAEs) in the laboratory and simulated shaft experiments were 0.06 cm and 0.30 cm, respectively, validating the reliability of the point cloud processing algorithm. In the real shaft experiment, the maximum MAE was 0.48 cm, confirming the measurement accuracy of the monitoring system. Compared to manual measurements, the system reduced the measurement time by 48% and streamlined the process from 12 to 3 steps. These findings highlight the monitoring system’s centimeter-level accuracy, efficiency in reducing measurement time, simplification of the measurement process, and elimination of the need for human entry into the shaft.
13 November 2023 in Computer-Aided Design and Applications
Computer-Aided Design and Applications is an international journal on the applications of CAD and CAM. It publishes papers in the general domain of CAD plus in emerging fields like bio-CAD, nano-CAD, soft-CAD, garment-CAD, PLM, PDM, CAD data mining, CAD and the internet, CAD education, genetic algorithms and CAD engines. The journal is aimed at all developers and users of CAD technology to ptovide CAD solutions for various stages of design and manufacturing. The journal publishes all about Computer-Aided Design and Computer-Aided technologies.