Physical simulations of tribo contacts in internal combustion engines can act as a supporting tool to match upcoming guidelines and emission restrictions. In particular, the scuffing resistance of the contact between the piston ring and cylinder liner suffers under decreasing oil viscosity and limitation of antiwear additives. This paper aims to provide an experimental method to simulate the scuffing of the piston ring/cylinder liner-contact and to validate this method with real engine parts and the literature from engine tests. The experimental methodology uses a linear tribometer TE77 to test specimens from original piston rings and liners under reciprocating motion. Additionally, the ring specimen is given the opportunity to perform secondary movements (ring twisting, ring turning) and to run under deficient lubrication conditions similar to the engine. A specially designed test strategy enables the reproducible creation of seizure of the tribosystem. The seizure resistance of two engine oils, tested for validation, correlates with the known engine performance. Therefore, the model test system can be seen as a reproducible tool for simulating seizure of a ring/liner-system, showing similar trends and wear mechanisms as in an engine. Surface analysis depicts similarities between the scuffed surfaces of an engine and the model and discusses the origin of seizure based on the model specimens together with the relevant literature.

The common approach for the flow factor calculation is based on using the Reynolds equation to simulate the micro-level flow. However, for structured surfaces the fluid flow cannot be represented correctly, due to the assumptions made when deriving the Reynolds equation. In this work, a novel method using the Navier-Stokes equations for the calculation of the micro-level flow is presented and validated against results from Patir and Cheng. The three-dimensional lubrication gap was generated by a rough Gaussian random surface and a perfectly smooth moving counter surface, in order to be available for different numerical methods. The presented results illustrate similar trends for both the approaches. Additionally, the use of the Navier-Stokes equations allows for the observance of surface induced effects which cannot be resolved by the approach of Patir and Cheng. Furthermore, a numerical approach for a shear flow factor calculation with a rough moving surface is presented and validated against other simulation methods. While the validation is maintained with pressure- and temperature-independent density and viscosity, these effects will be taken into account for later research activities of textured surfaces.

The modification of surface geometries to reduce friction is an omnipresent topic of research. In nature, different low-friction surfaces, such as fish skins, exist. To transfer this knowledge to technical applications, for example, to journal or plain bearings, many numerical and experimental studies of textured surfaces have been performed. In this work, the influence of the geometric parameters (texture length $l$, width $b$, angle $\alpha$ and start position $x_{start})$ of a wedge-shaped texture on three different convergent oil film gaps was analyzed in full-film lubrication and compared with untextured oil film gaps. With the aid of a CFD (computational fluid dynamics) model, a comprehensive variation study was conducted, and the best-performing wedge-shaped texture was determined. The results show that an open texture at the inlet provides the largest improvement. Furthermore, it can be observed that the optimal relative texture width and absolute inlet height for the three investigated oil film gaps are similar. In contrast to the volume flow of the untextured geometry, the volume flow of the textured one is significantly higher, especially that perpendicular to the movement direction.

Specific surface textures may reduce the friction and increase the lifting forces in lubricated contacts. For the detrimental operating condition of mixed friction, wear is induced by the solid contact. In this study, a methodology for wear calculation in textured, lubricated contacts is presented that considers the wear-induced surface topography evolution. Based on the Reynolds differential equation, the mass-conserving cavitation model according to Jakobsson, Floberg, and Olsson (JFO), a wear-dependent asperity contact pressure curve and the wear equation according to Archard, wear in a wedge-shaped, textured lubrication gap was calculated. The results show the wear behavior of textured lubrication gaps. Based on the wear simulations, the tribological behavior of the textured surfaces compared to smooth surfaces is discussed. It is evident that textures, which improve the tribological performance in the hydrodynamic lubrication regime, are not necessarily associated with low wear values in a lubrication condition in the mixed friction regime. The analysis of the wear-dependent parameters initially showed a ‘recovery’ of the tribological system with increasing wear until the performance decreased again after a specific reversal point. This behavior is attributed to the relative position of the surface textures in the lubrication gap.

Optimizing the surface topography of cast iron crankshafts offers the opportunity to use this material as an alternative to steel in high-performance combustion engines. In the past, this was not possible due to the higher wear on bearing shells and the higher friction losses in relation to forged steel shafts. In order to find an optimized shaft micro topography, the friction and wear behavior of steel and cast iron shafts with different surface treatments were compared to each other, using a combined physical (experimental) and a virtual (computational) simulation approach. The experiments were carried out with a rotary tribometer using a journal bearing test configuration with the possibility to test real-life bearing shells and shaft specimens, manufactured from real-life crankshafts. In the experiments, a polished steel shaft with low bearing wear was effective. The optimization of cast iron crankshafts by a novel surface treatment showed a significant reduction of bearing wear in relation to the classical surface finishing procedures of cast iron shafts. A computational simulation approach, considering the real-life micro topography by using the Navier–Stokes equations for the calculation of micro hydrodynamics, supports the assessment of fluid friction. The virtual simulation shows, in accordance to the experimental results, only a minor influence of the investigated shaft topographies on the fluid friction. Further optimization of shaft surfaces for journal bearing systems seems possible only by the usage of patterned micro topographies.

This study analyzes the influence of nine distinct texture geometries on a convergent oil film gap using a simulation model. The geometrical dimensions of the textures are characterized by the texture area density, $S_{tex.,A}$ and the ratio of the textured-to-untextured area ($A_{tex.}/A_0)$. The results show that different texture geometries optimize the tribological performance depending on the value of $S_{tex.,A}$. Rectangular textures with variable widths (85% of the texture length $a_{tex.}$) significantly enhance lifting and the drag force across a broad range of $S_{tex.,A}$. Furthermore, rectangular textures with a constant width (85% of the global width $b_0$) show the best improvement within this study. The investigation also reveals that a small texture pitch angle, ${\alpha }_{tex}$, further enhances tribological performance.