Graphene-based photodetectors have demonstrated mechanical flexibility, large operating bandwidth, and broadband spectral response. However, their linear dynamic range (LDR) is limited by graphene’s intrinsic hot-carrier dynamics, which causes deviation from a linear photoresponse at low incident powers. At the same time, multiplication of hot carriers causes the photoactive region to be smeared over distances of a few micrometers, limiting the use of graphene in high-resolution applications. We present a novel method for engineering photoactive junctions in FeCl₃-intercalated graphene using laser irradiation. Photocurrent measured at these planar junctions shows an extraordinary linear response with an LDR value at least 4500 times larger than that of other graphene devices (44 dB) while maintaining high stability against environmental contamination without the need for encapsulation. The observed photoresponse is purely photovoltaic, demonstrating complete quenching of hot-carrier effects. These results pave the way toward the design of ultrathin photodetectors with unprecedented LDR for high-definition imaging and sensing.

As a two-dimensional semimetal, graphene offers clear advantages for plasmonic applications over conventional metals, such as stronger optical field confinement, in situ tunability, and relatively low intrinsic losses. However, the operational frequencies at which plasmons can be excited in graphene are limited by the Fermi energy E_F, which in practice can be controlled electrostatically only up to a few tenths of an electronvolt. Higher Fermi energies open the door to novel plasmonic devices with unprecedented capabilities, particularly at mid-infrared and shorter-wave infrared frequencies. In addition, this grants us a better understanding of the interaction physics of intrinsic graphene phonons with graphene plasmons. Here, we present FeCl₃-intercalated graphene as a new plasmonic material with high stability under environmental conditions and carrier concentrations corresponding to E_F > 1 eV. Near-field imaging of this highly doped form of graphene allows us to characterize plasmons, including their corresponding lifetimes, over a broad frequency range. For bilayer graphene, in contrast to the monolayer system, a phonon-induced dipole moment results in increased plasmon damping around the intrinsic phonon frequency. Strong coupling between intrinsic graphene phonons and plasmons is found, supported by ab initio calculations of the coupling strength, which are in good agreement with the experimental data.

Optical resonances of crystalline Si nanopillar arrays on a Si substrate are studied using optical reflectivity and Raman spectroscopy. When the nanopillars are arranged in a two-dimensional lattice, a collective resonance is observed in the reflection spectra which is absent for randomly distributed nanopillars. The resonance is due to coherent oscillations in nanopillars, can be tuned spectrally by the nanopillar diameter and lattice period, and strongly suppresses reflection from the Si surface. Raman scattering demonstrates that the reduced reflectivity is accompanied by increased electromagnetic field confined in Si, thus suggesting potential application of the lattice resonance in surface enhanced spectroscopy and thin film solar cells.

Monitoring air quality is crucial for understanding and improving public health. There is interest in developing ultra-sensitive, low-power, cost-effective sensors. This work demonstrates that structural modulation of Sn nanoparticles through controlled deposition and oxidation enables a transition from metallic to semiconducting percolative networks, significantly enhancing NO₂ sensing performance at room temperature. The proposed percolation-driven sensing mechanism provides a new framework for understanding charge transport and gas interaction in nanostructured metal oxide systems. The nanoparticles are deposited near the percolation threshold for electrical conduction and, upon exposure to air, consist of a tin core and an amorphous Sn₃O₄ surface. Post-deposition heating in air at 320 °C for two hours forms SnO and Sn₃O₄ on top of the gold electrodes and polycrystalline SnO in the tetragonal litharge phase, known as Romarchite, on the glass between the electrodes. Both as-deposited and heat-treated sensors were capable of detecting NO₂ at room temperature, with a limit of detection in the parts-per-billion range. A percolation model is used to explain their operating currents, in which NO₂ reacts at nanoparticle gaps and intra-grain boundaries to form charge-depletion regions that primarily determine their resistance. Heat treatment has also been found to cause disproportionation of SnO, resulting in tin-rich precipitates and increasing the operating current to the milliampere range. These precipitates, although oxidized on their surfaces when exposed to air, may serve as bridges that reduce the total resistance of the percolating paths.