The specific impulse of solid rocket motors is much lower than that of liquid rocket motors due to limitations in solid propellant formulations. Inspired by the nuclear thermal rockets, the concept of helium injected solid–gas hybrid rocket motors (SGHRMs) is innovatively proposed and its thrust performance is numerically investigated in the present study. The injected helium is regarded as a working medium with strong expansion capacity, and the high-temperature combustion gas of the solid propellant is used as a heat source to heat the helium. Then, the mixed gas including the combustion gas and helium flows through the nozzle producing high boost thrust. Results show that the maximum specific impulse gain is up to 4.92%, and by adjusting the helium injection ratio from 0 to 2:1, the thrust regulation range of 100%–303% is achieved. When the helium is injected from the motor head, mixed gas with various helium fraction exhibits stratified flow characteristics. Hence, the mechanism of specific impulse gain can be elucidated by one-dimensional internal ballistics analysis. That is, mixed gas with a low helium mass fraction can significantly stimulate velocity gain with a slight reduction in total temperature, thereby increasing the specific impulse. However, mixed gas with a high helium mass fraction significantly reduces the total temperature, leading to a decreased expansion ability and a corresponding drop in the specific impulse. Finally, competition between mixed gases with various helium fractions determines the specific impulse gain level of SGHRMs.
A solid rocket motor (SRM) with a high aspect ratio that performs normally during ground tests may experience instability during flight. To address this issue, this study employs the pulse triggering method and the numerical approach of two-way fluid–structure interaction to investigate the mechanisms behind the SRM instability resulting from distinctions between on-ground and in-flight conditions. The results indicate that the main distinctions between the on-ground and in-flight conditions for SRMs are the strong constraints during the ground test, as well as aerodynamic forces and aerodynamic heating during flight. The strong constraints in the ground test effectively suppress structural vibrations by limiting displacements. In flight conditions, the aerodynamic heating reduces the strength of the SRM casing and aerodynamic forces provide sustained energy input for structural vibrations during flight. The mechanism for the ground/flight differences that induce SRM instability is that the structural natural frequencies are reduced by aerodynamic heating and the first-order acoustic frequency increased by the propellant regression approach reaches the resonance condition. Therefore, an instability factor Φ is proposed to represent the resonance relationship between the structural natural modes and the acoustic mode of SRMs. Furthermore, the closer the frequency of the aerodynamic forces is to the resonance frequency of the acoustic-structure coupling, the more pronounced the SRM instability.
Compared to liquid rocket motors, solid rocket motors have lower specific impulse and weaker thrust regulation capabilities. Therefore, the concept of helium-injected solid–gas hybrid rocket motor (SGHRM), which can effectively improve specific impulse and achieve thrust regulation function, was introduced by our research group. The injected helium is used as working medium with strong expansion capacity, and the high-temperature combustion gas is used as a heat source to heat the helium. A mixture of gases, including combustion gas and helium, then flows through the nozzle producing high thrust. In the present paper, swirling helium is injected into the combustion chamber to further improve the specific impulse of SGHRM. The effects of helium mass flow and swirl intensity are numerically investigated, and the mechanism of specific impulse gain is revealed by one-dimensional gas dynamics analysis. Results indicate a maximum specific impulse gain of 11.28% and a thrust adjustment range of 100%–225% by varying the helium injection ratio. Compared with the axial helium injection scheme, the swirling helium injection scheme effectively improves the mixing degree of helium and combustion gas, and the behavior of rotating helium passing through combustion gas enhances the thermal convection. These two actions together strengthen the heat transfer from combustion gas to helium, effectively improve the total temperature and working capacity of helium, and further increase the exit velocity of mixed gas. In addition, the centrifugal force caused by the swirl elevates the mass flux in the velocity increase zone near the wall and further enhances the specific impulse.
To investigate the evolution characteristics of motor performance during starting/stopping helium injection, a transient numerical simulation of the solid–gas hybrid rocket motor is conducted using the propellant combustion model. Results show that during the starting helium injection process, large-scale vortex rings caused by the shear effect of helium and combustion gas appear at the head of the high-velocity helium jet, and the growth and fragmentation behaviors of vortex rings promote the mixing of helium and combustion gas. Thus, a shorter regulation time of helium injection strengthens the initial momentum of vortex rings and achieves a higher mixing degree. In this condition, helium fills the recirculation zone of the post-combustion chamber, making the flow field of a motor reach a stable operation state. Finally, within 200 ms after the helium mass flow rate reaches 1 kg/s, the thrust and specific impulse are increased by 38.3% and 13.8%, respectively, while the nozzle exit temperature is decreased by 57%. However, when the initial momentum of the vortex ring is relatively small, the mixing degree is poor in the post-combustion chamber. Subsequently, periodic vortex shedding causes periodic fluctuations in the mixing degree in the nozzle, resulting in periodic oscillations with an amplitude of approximately 1% in motor performance. During the stopping helium injection process, within 200 ms after the helium mass flow rate is regulated to 0 kg/s, the motor thrust and specific impulse gradually recover to a level comparable to that observed before helium injection, and a shorter regulation time results in a faster variation in motor performance.
27 January 2026 in International Journal of Thermal Sciences
Utilizing high-energy solid powder fuel is the key path to enhancing the performance of rotating detonation engines. However, traditional solid fuels have problems such as slow reaction kinetics or long ignition delay, which restrict their energy release efficiency in detonation environments. The thermal decomposition temperature of AlH3 is low, and its hydrogen storage density is high, which can provide a feasible path for gas–solid two-phase detonation. This paper employs the Eulerian–Lagrangian method to solve the gas–solid two-phase detonation problem, and the effects of different parameters on the flow field and detonation wave propagation characteristics are considered. The results show that the detonation wave exhibits two spatially separated heat release zones behind a single shock front. The forward reaction zone is dominated by the H2–O2 homogeneous reaction, while the rearward reaction zone is dominated by the Al(s)–O2 heterogeneous reaction. As the equivalence ratio increases, the wave velocity and pressure first increase and then decrease. The same non-monotonic trend is observed when the inlet total temperature is raised. Excessive equivalence ratio reduces the energy contribution of aluminum combustion, shifting the detonation toward hydrogen-dominated propagation, whereas excessive inlet temperature causes premature AlH3 decomposition ahead of the wave. The inlet mass flow rate monotonically increases the front pressure, but the wave velocity exhibits an optimal range. At excessively low flow rates, aluminum particles burn incompletely; at excessively high flow rates, particles tend to escape through the triple wave point, both of which degrade the effective fuel utilization.