This paper opens up a new perspective on the aerodynamic performance of a wind turbine airfoil. More specifically, the paper deals with a steady, incompressible two-phase flow, consisting of air and two different concentrations of sand particles, over an airfoil from the National Renewable Energy Laboratory, NREL S809. The numerical simulations were performed on turbulence models for aerodynamic operations using commercial computational fluid dynamics (CFD) code. The computational results obtained for the aerodynamic performance of an S809 airfoil at various angles of attack operating at Reynolds numbers of Re = 1 × 106 and Re = 2 × 106 in a dry, dusty environment were compared with existing experimental data on air flow over an S809 airfoil from reliable sources. Notably, a structured mesh consisting of 80,000 cells had already been identified as the most appropriate for numerical simulations. Finally, it was concluded that sand concentration significantly affected the aerodynamic performance of the airfoil; there was an increase in the values of the predicted drag coefficients, as well as a decrease in the values of the predicted lift coefficients caused by increasing concentrations of sand particles. The region around the airfoil was studied by using contours of static pressure and discrete phase model (DPM) concentration.
1 January 2007 in International Journal of Low-Carbon Technologies
This paper describes the development of an experimental setup to investigate the performance of heat pipes as capillary pumps. The experimental setup and the research that was performed by LFME was part of an EU funded research project called TRI-GEN EGD that aims in the overall development of a novel Tri-generation Electrogasdynamic converter system. The capillary pump will be used to pump the working fluid of the system using external waste heat. Furthermore, since the capillary pump has no moving parts it will provide the system with greater reliability. The experimental setup designed and constructed by LFME is a Capillary Pumped Loop (CPL). A CPL is a closed loop system that pumps liquid by passive means, based on the operating principles of heat pipes. Specifically capillary forces are generated on a porous structure that exists in the evaporation section and is responsible for pushing the working fluid from a high temperature source to a low temperature sink. In this paper, a brief description of the experimental setup that was constructed and a description of the experimental procedure that was followed will be given together with some results that were obtained for various configurations.
8 August 2013 in International Journal of Low-Carbon Technologies
Capillary pump loop (CPL) is a two-phase heat transfer device considered as a useful solution for thermal control applications in spacecrafts, satellites and electronic components. The purpose of this paper is to study various aspects of the working state of the CPL evaporator. A two-dimensional computational model was developed in order to analyze the flow and the phase transformation inside a cylindrical evaporator. At the present analysis, different cases were studied by changing liquid saturation temperature, inclination angle of the evaporator and the length of the porous heated wick. Water, ammonia, acetone and freon-134 were used as working liquids for numerical experiments. Results present the evaporator capability to vaporize each working liquid and find out its possibility of dry-out causing failure. This information is useful in choosing the best working liquid for an evaporator, enabling bigger amounts of heat to be transferred.
27 November 2013 in International Journal of Low-Carbon Technologies
The purpose of this paper is to present a theoretical analysis of the capillary pumped loop (CPL) performance using different working liquids. CPL is a passive heat transfer device, using no mechanical pump to circulate the working liquid, usually composed of a liquid tank, an evaporator, a condenser, a liquid and a vapor line. Heat load is applied on the external surface of the evaporator, partially transferred to the wick inside. Because of this heat load capillary forces are developed inside the porous structure, due to meniscus formation between liquid and vapor surface of the liquid, causing a pressure oscillation capable to pump the flow out of the evaporator. In this paper CPL performance is evaluated using different working liquids, such as water, ammonia, acetone and freon-134. These have different thermophysical properties such as latent heat, viscosity and density, causing different behavior when used as working liquid. Water was found more stable for higher temperature differences, due to higher latent heat of vaporization, while ammonia could take advantage of its viscosity for small temperature differences.
1 April 2007 in International Journal of Low-Carbon Technologies
The objective of this paper is to present a theoretical investigation of the operational characteristics on a small-scale Capillary Pump Loop (CPL), focused on the CPL capacity to create flow in addition to its heat transfer capacity. A typical design of a CPL is composed of a capillary evaporator, a condenser, a two-phase reservoir, liquid and vapour lines. The capillary evaporator generates the required pressure pumping for moving the working fluid from the condenser to the evaporator section. The fundamental principles of the proposed modelling are: The overall pressure drop in the loop must be less than the maximum capillary pressure in order to ensure that the system will operate continuously. The major components of the CPL pressure drop are related to the flow in the wick structure, condenser, vapour and liquid lines. The wick structure present in the evaporator causes a flow restriction that affects the CPL performance, which is dependent on the wick permeability, a property of the porous material that describes its ability to transport the liquid under an applied pressure gradient. An experimental lab-scale installation is used for the validation of the theoretical analysis. The results showed that the proposed CPL modelling is able to describe the CPL performance very well.
This paper concentrates on a new configuration for a wind turbine, named KIONAS. The main purpose is to determine the performance and aerodynamic behavior of KIONAS, which is a vertical axis wind turbine with a stator over the rotor and a special feature in that it can consist of several stages. Notably, the stator is shaped in such a way that it increases the velocity of the air impacting the rotor blades. Moreover, each stage’s performance can be increased with the increase of the total number of stages. The effects of wind velocity, the various numbers of inclined rotor blades, the rotor diameter, the stator’s shape and the number of stages on the performance of KIONAS were studied. A FORTRAN code was developed in order to predict the power in several cases by solving the equations of continuity and momentum. Subsequently, further knowledge on the flow field was obtained by using a commercial Computational Fluid Dynamics code. Based on the results, it can be concluded that higher wind velocities and a greater number of blades produce more power. Furthermore, higher performance was found for a stator with curved guide vanes and for a KIONAS configuration with more stages.