Group‐10 transition metal dichalcogenides (TMDs) with distinct optical and tunable electrical properties have exhibited great potential for various optoelectronic applications. Herein, a self‐powered photodetector is developed with broadband response ranging from deep ultraviolet to near‐infrared by combining FA_1−xCs_xPbI₃ perovskite with PdSe₂ layer, a newly discovered TMDs material. Optoelectronic characterization reveals that the as‐assembled PdSe₂/perovskite Schottky junction is sensitive to light illumination ranging from 200 to 1550 nm, with the highest sensitivity centered at ≈800 nm. The device also shows a large on/off ratio of ≈10⁴, a high responsivity (R) of 313 mA W⁻¹, a decent specific detectivity (D*) of ≈10¹³ Jones, and a rapid response speed of 3.5/4 µs. These figures of merit are comparable with or much better than most of the previously reported perovskite detectors. In addition, the PdSe₂/perovskite device exhibits obvious sensitivity to polarized light, with a polarization sensitivity of 6.04. Finally, the PdSe₂/perovskite detector can readily record five “P,” “O,” “L,” “Y,” and “U” images sequentially produced by 808 nm. These results suggest that the present PdSe₂/perovskite Schottky junction photodetectors may be useful for assembly of optoelectronic system applications in near future.

Energy conversion efficiency losses and limits of perovskite/silicon tandem solar cells are investigated by detailed balance calculations and photon management. An extended Shockley–Queisser model is used to identify fundamental loss mechanisms and link the losses to the optics of solar cells. Photon management is used to minimize losses and maximize the energy conversion efficiency. The influence of photon management on the solar cell parameters of a perovskite single-junction solar cell and a perovskite/silicon solar cell is discussed in greater details. An optimized solar cell design of a perovskite/silicon tandem solar cell is presented, which allows for the realization of solar cells with energy conversion efficiencies exceeding 32%.

Hydrogenated amorphous silicon (a-Si:H) has been effectively utilized as photoactive and doped layers for quite a while in thin-film solar applications but its energy conversion efficiency is limited due to thinner absorbing layer and light degradation issue. To overcome such confinements, it is expected to adjust better comprehension of device structure, material properties, and qualities since a little enhancement in the photocurrent significantly impacts on the conversion efficiency. Herein, some numerical simulations were performed to characterize and optimize different configuration of amorphous silicon-based thin-film solar cells. For the optical simulation, two-dimensional finite-difference time-domain (FDTD) technique was used to analyze the superstrate (p-i-n) planar amorphous silicon solar cells. Besides, the front transparent contact layer was also inquired by using SnO2:F and ZnO:Al materials to improve the photon absorption in the photoactive layer. The cell was studied for open-circuit voltage, external quantum efficiency, and short-circuit current density, which are building blocks for solar cell conversion efficiency. The optical simulations permit investigating optical losses at the individual layers. The enhancement in both short-circuit current density and open-circuit voltage prompts accomplishing more prominent power conversion efficiency. A maximum short-circuit current density of 15.32â¯mA/cm2 and an energy conversion efficiency of 11.3% were obtained for the optically optimized cell which is the best in class amorphous solar cell. Keywords: Superstrate p-i-n, Power loss, Quantum efficiency, Short circuit current, FDT

In thin-film solar cells, the photocurrent conversion productivity can be distinctly boosted-up utilizing a proper back reflector. Herein, the impact of different smooth and textured back reflectors was explored and effectuated to study the optical phenomena with interface engineering strategies and characteristics of transparent contacts. A unique type of wet-chemically textured glass-substrate 3D etching mask used in superstrate (p–i–n) amorphous silicon-based solar cell along with legitimated back reflector permits joining the standard light-trapping methodologies, which are utilized to upgrade the energy conversion efficiency (ECE). To investigate the optical and electrical properties of solar cell structure, the optical simulations in three-dimensional measurements (3D) were performed utilizing finite-difference time-domain (FDTD) technique. This design methodology allows to determine the power losses, quantum efficiencies, and short-circuit current densities of various layers in such solar cell. The short-circuit current densities for different reflectors were varied from 11.50 to 13.27 and 13.81 to 16.36 mA/cm2 for the smooth and pyramidal textured solar cells, individually. Contrasted with the comparable flat reference cell, the short-circuit current density of textured solar cell was increased by around 24%, and most extreme outer quantum efficiencies rose from 79 to 86.5%. The photon absorption was fundamentally improved in the spectral region from 600 to 800 nm with no decrease of photocurrent shorter than 600-nm wavelength. Therefore, these optimized designs will help to build the effective plans next-generation amorphous silicon-based solar cells.