Digital Elevation Models (DEMs) are widely used as a proxy for bathymetric data and several studies have attempted to improve DEM accuracy for hydrodynamic (HD) modeling. Most of these studies attempted to quantitatively improve estimates of channel conveyance (assuming a non-braided morphology) rather than accounting for the actual channel planform. Accurate representation of river conveyance and planform in a DEM is critical to HD modeling and can be achieved with a combination of remote sensing (e.g., satellite image) and field data, such as water surface elevation (WSE). Therefore, the objectives of this study are (i) to develop an algorithm for predicting channel conveyance and characterizing planform via satellite images and in situ WSE and (ii) to estimate discharge using the predicted conveyance via an HD model. The algorithm is named River Bathymetry via Satellite Image Compilation (RiBaSIC) and uses Landsat satellite imagery, Shuttle Radar Topography Mission (SRTM) DEM, Multi-Error-Removed Improved-Terrain (MERIT) DEM, and observed WSE. The algorithm is tested on four study areas along the Willamette River, Kushiyara River, Jamuna River, and Solimoes River. Channel slope and predicted hydraulic radius are subsequently estimated for approximating Manning’s roughness factor. Two-dimensional HD models using DEMs modified by the RiBaSIC algorithm and corresponding Manning’s roughness factors are employed for discharge estimation. The proposed algorithm can represent river planform and conveyance in single-channeled, meandering, wandering, and braided river reaches. Additionally, the HD models estimated discharge within 14–19% relative root mean squared error (RRMSE) in simulation of five years period.
This study assessed the uncertainty in flood impact assessment (FIA) that may be introduced by errors in moderate resolution regional and moderate resolution global Digital Elevation Models (DEM). One arc-second National Elevation Dataset (NED) and one arc-second Shuttle Radar Topography Mission (SRTM) DEMs were selected to represent moderate resolution regional and global DEMs. The relative performance for scenarios based on each of the DEMs was compared to a “control” terrain (combination of surveyed river bathymetry and a 1/3 arc-second LiDAR for floodplains)-based scenario. Furthermore, a conveyance-based DEM correction technique was applied to the DEMs for investigating the suitability of the technique on selected DEMs, and determining subsequent improvement in the FIA. The May 2010 flood on the Cumberland River near Nashville, TN, was selected as the case study. It was found that the hydraulic properties necessary to implement the selected DEM correction technique could be more readily estimated from NED compared to SRTM. However, this study also prescribed alternate methods to extract necessary hydraulic properties if the DEM quality was compromised. NED-based hydrodynamic modeling resulted in a high overestimation of the simulated flood stage, but the SRTM-based model was unable to produce any reasonable result prior to DEM correction. Nevertheless, after DEM correction, both models became stable and produced less error. Error in simulated flood consequence (i.e., total structures affected and total loss in dollars) also dropped accordingly, following the DEM correction. Therefore, application of this conveyance-based correction technique is reasonably effective on both moderate-resolution regional and global DEMs. The effectiveness of the technique on moderate resolution global DEM underscores the potential for users of remote and data-poor areas.
1 February 2020 in Journal of Hydrologic Engineering
Digital elevation models (DEMs) are widely used for hydraulic modeling, but one of the challenges in using a DEM for hydraulic modeling is its limitations in accurately representing the channel conveyance. This limitation is usually disregarded because the collection of bathymetry data is time and resource intensive, and it is often unavailable for well-gauged watersheds as well. Thus, a DEM-based hydraulic model may lead to less accurate conclusions even if detailed hydrologic data are available. The situation is more challenging in large and morphologically active river systems because DEMs only represent the river condition of their acquisition time. Therefore, the objectives of this research are to (1) develop a DEM correction method for predicting channel conveyance at the watershed scale and (2) demonstrate the significance of riverbed-level change for flood risk assessment in the Obion River. The proposed DEM correction method is called Slope Adjusted Mean Bed Level Elevation (SAMBLE) and utilizes the hydrologic data of a watershed to predict average riverbed level and thus channel conveyance at a watershed scale. It is tested on the Obion River watershed in northwest Tennessee. Analysis of the results showed that the SAMBLE method can predict average riverbed level with less than 1 m error that is more accurate than the best available Light Detection and Ranging (LiDAR) DEM for the Obion River watershed. Additionally, it can predict riverbed-level changes using time series of hydrologic data. The significance of riverbed-level change on flood risk is also demonstrated by estimating aggradation-degradation (via SAMBLE) in a morphologically active segment of the Obion River.
30 December 2022 in Jawra Journal of the American Water Resources Association