Flow past a heated cylinder at constant surface temperature is computationally simulated and analyzed in the laminar regime at moderate buoyancy. The parameters governing the flow dynamics are the Reynolds number, Re, the Richardson number, Ri, and the Prandtl number, Pr. We perform our computations in the range 10 ≤ Re ≤ 35, for which the flow past an unheated cylinder results in a steady separation bubble, and vary the other two parameters in the range 0 ≤ Ri ≤ 2, 0.25 ≤ Pr ≤ 100. The heat transfer from the entire cylinder surface, quantified by the average Nusselt number Nuavg, is shown to obey Nuavg = 0.7435Re0.44Pr0.346 in the mixed convection regime we investigate. For a fixed Re and Pr, the flow downstream of the cylinder becomes asymmetric as Ri is increased from zero, followed by a complete disappearance of the vortices in the recirculation bubble beyond a threshold value of Ri. For a fixed Re and Ri, the vortices in the recirculation bubble are again observed to disappear beyond a threshold Pr, but with the reappearance of both the vortices above a larger threshold of Pr. In the limit of large Pr, the time-averaged flow outside the thermal boundary layer but within the near-wake region regains symmetry about the centerline and ultimately converges to a flow field similar to that of Ri = 0; in the far-wake region, however, we observe asymmetric vortex shedding for moderate Pr. The thermal plume structure in the cylinder wake is then discussed, and the plume generation is identified at points on the cylinder where the Nusselt number is a local minimum. The difference between the plume generation and the flow separation locations on the cylinder is shown to converge to zero in the limit of large Pr. We conclude by plotting the lift and drag coefficients as a function of Ri and Pr, observing that CD decreases with Ri for Pr < Prt (and vice versa for Pr > Prt), where Prt ≈ 7.5.
A novel and effective hybrid technique, which involves active surface heating strategies in conjunction with the use of passive splitter plates in the wake of the cylinder, is proposed. In this report, we present the results of a numerical investigation on the two-dimensional, laminar mixed convection flow over a circular cylinder with a hot rigid splitter plate attached to it on the wake side. A projection algorithm-based finite volume method is employed to obtain the solution of the coupled, nonlinear governing partial differential equations subjected to Courant–Friedrichs–Lewy conditions. The isothermal heating of the splitter plate under the influence of the gravity field generates an upward buoyancy force in the wake of the cylinder. For different length-to-diameter (L/D) ratios, the effect of heating on aerodynamic, wake, and heat transfer characteristics has been studied for a wide range of parameters; 75 ≤Re≤ 150, 0 ≤Ri≤ 1, and 0.5 ≤L/D≤ 1 at Pr = 0.7. It is observed that the hot splitter plate would bring about conspicuous changes such as asymmetry in the vortex shedding behind the cylinder at low Reynolds numbers. The outcomes demonstrate a notable improvement in convective heat transfer and drag, with gains of up to 7% and 15%, respectively. It is found that the rate of heat transfer and vortex shedding frequency decrease with an increase in L/D ratio. Correlations for the estimation of Strouhal number and Nusselt number have also been proposed which helps provide a more thorough understanding of thermal and aerodynamic features of the hybrid approach.
Numerical simulations are performed to investigate the effect of the Reynolds number (Re) on flow over curved plates. Concave and convex plates, obtained by introducing curvature on a flat plate, are analyzed in the Reynolds number range 0.1 ≤Re≤ 120. It is observed that for a concave plate, the separation point is dependent on Re, while for a convex plate, the flow separates from the outermost tips for all Reynolds numbers. The analysis of time-averaged quantities reveals that concave and convex plates behave differently for the same Reynolds number. In the steady flow regime, visualization of streamlines reveals the presence of a recirculation bubble on the front side of the concave plate, even for the lowest Reynolds number (Re = 0.1). However, at higher Reynolds numbers (Re = 110, 120), the near wake of concave plate witnesses secondary and tertiary recirculating entities. The present simulations also report the unique phenomenon of vortex realignment and divergence of vortex street in the wake of a concave plate. For a convex plate, the vortex realignment is followed by the movement of upper and lower vortices as two parallel vortex streets. The existence of multiple instabilities is another highlight in the near and far wakes of the concave plate, some of which arise due to the secondary vortex interactions. A comprehensive analysis further reveals a handful of novel phenomenal occurrences in the wake of concave surfaces.
Flow past a heated two-dimensional cylinder in the laminar regime is investigated. A hybrid finite element–finite volume method is used to solve Navier–Stokes and energy equations. The vortex shedding frequency defined nondimensionally as Strouhal number is observed to be increasing with heating. Vortex shedding behind heated cylinder exhibits asymmetry in wake region due to stable and unstable density stratification below and above the cylinder, respectively. A negative lift is generated due to heating, in an otherwise symmetric zero time-averaged lift configuration, due to skewness in vortex shedding towards the direction of buoyancy. We also note that the heating brings down the drag for the cases considered here. The thermal energy transport due to convection, defined by nondimensional Nusselt number is found to increase only marginally with cylinder heating.
31 December 2022 in Journal of Mechanical Science and Technology