Acoustic Doppler current profilers (ADCPs) use the signal scattered back from small suspended drifting particles, such as suspended sediments and planktonic species, to measure water current velocity. Additionally, ADCPs detect signals scattered from fish and other pelagic organisms, but these signals are generally treated as noise and rejected during data processing. However, these rejected signals can contain information on fish movement, which presents an opportunity to extend the application of ADCP technology as a tool for monitoring fish activity. We compare discrete target counts made using an ADCP with those of a split‐beam echosounder in a region of high tidal currents in the Bay of Fundy. The comparison was achieved using a self‐contained bottom‐mounted frame equipped with both a 600‐kHz Teledyne RD Instruments Workhorse ADCP and a 120‐kHz BioSonics DTX Submersible split‐beam echosounder system. The discrete targets were identified using a combination of signal correlation and volume backscatter (SV) thresholds in the ADCP data and using a fish tracking algorithm in the split‐beam echosounder data. The resulting ADCP discrete target counts agreed with fish tracking counts made from the co‐located split‐beam echosounder. Notably, discrete targets recorded by the ADCP could be differentiated from entrained air using a high signal correlation threshold. This method can expand the application of ADCP data for biophysical assessments for fisheries management and could be of particular use in rivers and tidal channels.
28 April 2021 in Journal of Geophysical Research: Earth Surface
Prior studies demonstrate that bottom velocity measurements from Doppler sonar systems are proportional to bedload transport rates. These observations suggest that acoustically based systems offer a capability for rapid sampling of bedload transport processes. Before these measurements can be fully utilized, validation and understanding of the sampling mechanism are essential. We explore the measurement mechanism through a series of laboratory trials with a field instrument, the multi‐frequency coherent Doppler profiler (MFDop). The MFDop system is a multi‐frequency (1.2–2.2 MHz), bistatic Doppler sonar that provides three‐component ensemble‐averaged velocity profiles over a ∼30 cm depth interval with up to 1 mm resolution at a rate of 50 profiles/sec. Tests of the MFDop system were carried out in the main flume in field‐scale conditions at the St. Anthony Falls Laboratory (SAFL) using 1 ms−1 mean flows over a mobile bed of sand with median grain size d50 = 0.4 mm. We find agreement between MFDop transport measurements and measurements based on bedform migration rates, and sediment traps built into the SAFL flume. Predictions using the Meyer‐Peter and Müller (1948) empirical equation closely match our observations while in contrast, predictions using the Nielsen (1992) equation are a factor of two higher.
Oceanographic data collected during seismic surveys have potential to provide a significant resource for oceanographic research. In this paper, acoustic Doppler current profiler (ADCP) data collected during the Chevron 2011 North East Grand Banks survey are analysed. The survey took place in a 32,000-km2 area in the North East Grand banks, Orphan Basin region in water depths ranging from 100 to 1500 m and notably, the survey area is crossed by the offshore branch of the Labrador current. Data quality is evaluated by comparing velocities before and after ship turns where we find no significant velocity bias. The ADCP data are compared to data products from the CONCEPTS global ice ocean prediction system operational ocean model. ADCP data and model output agree qualitatively with the model reproducing the long-term fluctuations seen in the data. At higher frequencies between 0.3 and 2.0 cycles/day, the model tends to under-represent the current velocities by about 20%, but the spectral peak associated with inertial oscillations is well resolved. Comparisons of drift track predictions based on the ADCP observations and model output show rms displacement differences of 8 km after 24 h and ∼10 km separations for drift tracks with length under 50 km.
Zedel, L., and Cyr-Racine, F-Y. 2009. Extracting fish and water velocity from Doppler profiler data. – ICES Journal of Marine Science, 66: 1846–1852. Doppler current profilers are optimized for measuring water velocities, but have the demonstrated capability to measure fish swimming speeds. This is possible when fish form schools that are large enough for all multiple Doppler sonar beams to sample the fish speeds at the same time. In situations where fish are not present in at least three acoustic beams, it is impossible to extract fish velocity with the data-processing algorithms normally used to extract water velocity. We present an alternative method of analysing Doppler sonar data that treats data from individual acoustic beams independently, so that velocities can be extracted when fish appear intermittently in the sonar beams. The method determines the variance for each velocity estimate so that data averaging can be adjusted to achieve the desired accuracy. The algorithm is applied to extract both water and fish velocities from Doppler profiler observations of overwintering Atlantic cod (Gadus morhua) in Smith Sound, Newfoundland. Currents in this enclosed coastal area are slow (∼10 cm s−1), and the fish appear to move passively with the water much of the time. However, there are times when the fish have velocities different from those of the water, and profiles averaged over 20 d show clear differences in fish and water velocities.
10 May 2022 in IEEE Journal of Oceanic Engineering
A challenge in exploiting tidal energy resources is to determine the most suitable sites for development, and as the industry grows, to monitor the progressive impacts of tidal farms on the flow field and sediment transport regimes. A feasibility experiment was carried out with the fluvial acoustic tomography (FAT) system to assess the combined effects of irregular bathymetry, horizontal and vertical sound-speed gradients, and macroturbulence on the quality of FAT-estimated velocities. The experiment involved reciprocal transmissions at 30-s intervals for four days with two 7-kHz broadband transceivers. To determine the origin and potential interpretive value of the frequent multiple arrivals in the unstratified, highly-turbulent flow conditions, we performed a series of simulations with the Bellhop3D model. We demonstrate that the multiple arrivals mainly arise from out-of-plane sound propagation paths resulting from the effects of the local bathymetry. The maximum mean difference between FAT-estimated currents and the coincident moving-vessel acoustic Doppler current profiler (ADCP) transects is found to be less than 10%. Comparisons are also made between velocity spectra during the full flood and the ebb determined using the FAT velocities and the vertically-averaged velocities from a bottom-mounted ADCP deployed in a later experiment. The spectra exhibit similar shapes in the frequency and wave number overlap regions, indicating that FAT is able to detect macroturbulence. Good agreement is also obtained between the sound-speed estimates based on the travel time and those from in situ temperature and salinity data. Overall, the results demonstrate the potential of shallow acoustic tomography for monitoring environmental conditions in high-flow tidal channels.
It is well known that rainfall rate can be estimated by analyzing the spectral character and level of the underwater sound that it generates. There have been a few field reports of increased sound levels associated with the occurrence of snow; these reports suggest an increase in sound levels above 20 kHz. It has previously been demonstrated that snowflakes can generate both a small impact sound and a separate high frequency pulse that is consistent with the sound generated by a resonant bubble. One aspect that these earlier studies have not explored is the dependence of this sound generation on the type or intensity of snowfall. We report on observations of sound generated by snow falling into a tank of water, quantifying snowfall rate using an Optical Scientific precipitation gauge. Recorded signals allowed analysis of frequencies between 1 and 50 kHz. Using the classification scheme of the International Association of Hydrological Sciences for snow, seven distinct snow types, as well as rain and freezing rain, were observed with a range of precipitation rates. Snow types that produced a signal included column, needle, irregular crystal, graupel and ice pellet. Snow types for which no signal was detected were plate, stellar crystal and spatial dendrite. The previously reported rise in high frequency sound could not be distinguished unambiguously in the present data. A small peak at around 12 kHz was seen in spectra of some snow types similar to the characteristic 14 kHz peak seen in some rain-generated sounds. There was a clear correlation between sound level and snowfall rate at frequencies above 10 kHz.