Several studies have previously been conducted to improve the cooling performance of film cooling. However, most of the research has conducted experiments with film cooling holes on flat plates, and thus, the results of these studies do not encompass the influence of the complex mainstream behavior within the turbine passage on film cooling. In this study, three different film cooling hole configurations were installed on the endwall of a turbine linear cascade to measure adiabatic film cooling effectiveness and evaluate cooling performance. The film cooling holes compared in the experiment for film cooling effectiveness were a 7-7-7 fan-shaped hole (Baseline), a Baseline with a double-step structure at the hole exit (Staircase), and a Baseline with an additional expanded passage at the hole leading edge (Compound Expansion). A total of nine holes were manufactured on the turbine endwall to assess film cooling performance, as various factors, such as mainstream acceleration, secondary flow within the turbine passage, and so on, can influence film cooling. Adiabatic film cooling effectiveness was measured using the pressure-sensitive paint (PSP) technique. Mass flow ratios ranging from 0.25% to 1.25% of the mass flow rate of a single turbine passage were supplied to the plenum chamber within the test rig. As a result, all experimental results confirmed the impact of secondary flow within the turbine passage on film cooling. In the case of the Staircase, it exhibits an overall cooling trend similar to the Baseline. It shows small cooling performance degradation compared with Baseline due to lift-off, and its double-step structure laterally expanding results in better cooling performance at high mass flow ratio (MFR) conditions. For the Compound Expansion, at low MFR, the momentum of the coolant is lower compared with other configurations, leading to lower cooling performance due to the influence of secondary flow. However, at high MFR, the Compound Expansion provides wider protection compared with other hole geometries and shows high cooling performance.

The objective of this study is to implement a more realistic integrated analysis model for micro gas turbines by incorporating secondary flow and combustion efficiency into the existing model, which includes main engine components such as the compressor and turbine, and to validate this model by comparing it with test results. The study was based on the JetCat P300-RX, which has a maximum thrust level of 300 N. Simulations were performed using ANSYS CFX, employing the κ-ω SST turbulence model and a mixing plane interface between individual components. The eddy dissipation model (EDM), with a combustion efficiency of 90%, was used as the combustion model. A user subroutine was also applied for the power matching of the compressor and turbine to calculate the fuel flow rate in each iteration. For secondary flow, it was assumed that 3% of the total air flow rate would flow through the secondary path and be applied to the compressor and turbine. Simulations were conducted over a range of 30,000 to 104,000 RPM, with ground conditions evaluated, including altitude-simulated conditions. To validate the analysis model, engine performance metrics such as pressure ratio, air flow rate, fuel flow rate, and exhaust gas temperature (EGT) were compared with test results. The results demonstrated that errors were less than 5% for most engine performance metrics, except for EGT and fuel flow. The discrepancy in EGT was attributed to differences in the sensing methods, while the variation in fuel flow was found to be due to the lubrication system and losses due to the secondary air flow. Consequently, this study confirmed that the integrated simulation model accurately predicts engine performance. The results indicate that the integrated simulation model provides a more realistic prediction of overall engine performance compared to previous studies. Therefore, it can evaluate detailed thermo-fluid properties without the need for component performance maps, enhancing performance evaluation and analysis.

Modern gas turbines have evolved by increasing the turbine inlet temperature (TIT) to improve performance. This development has led to a demand for cooling techniques. Among these, the film cooling, which involves injecting compressed air through holes on the turbine surface, is a prominent cooling technique used to protect the turbine surface. In this study, a comparative analysis is conducted between the conventional fan-shaped film cooling hole, primarily used in film cooling techniques, and modified shapes achieved by altering the geometry of the film cooling hole based on a fan-shaped hole to assess and compare the cooling performance on a flat plate surface. The adiabatic film cooling effectiveness was measured for three film cooling holes, the Baseline of a 7-7-7 fan-shaped film cooling hole, namely, Staircase, which had a double-step at the hole exit, and Compound Expansion, which had an additional expanded flow path at the hole leading edge. The used measurement technique was the pressure-sensitive paint (PSP) technique, using nitrogen gas as the foreign gas, and experiments were conducted at a density ratio of 1.0 and blowing ratios ranging from 0.5 to 2.0. The results reveal that the modified holes featured wider lateral expansion at the hole exits, resulting in a broader distribution of the cooling effectiveness in the lateral direction compared to the Baseline. The Staircase shows a better performance, although an overall cooling effectiveness trend similar to that of the Baseline. Furthermore, the Compound Expansion demonstrates an enhancement in the cooling performance with an increased blowing ratio, notably achieving nearly double the cooling effectiveness compared to that of the Baseline at a blowing ratio of 2.0.