A scaling formulation is constructed for the hydrodynamic thrust by an undulatory propulsor based on the vortex dynamics. It states that the propulsion thrust is in scale with the square of Strouhal number and the relative speed of undulation and fish forward swimming, which implies an energy flux from the fish body to fluid. The higher the energy flux, the higher is the propulsion fish obtains. The results indicate that the scaling relation holds widely for different undulatory locomotion modes, where the slope factor of “thrust-energy flux” increases monotonously with the wavelength and Reynolds number. The full scaling law of the propulsion depends not only on the Strouhal number and Reynolds number, but also on the wavelength and the undulatory phase speed.
1 January 2015 in Theoretical and Applied Mechanics Letters
Different from birds and insects, bats have complex wing-deformation capacity to generate high aerodynamic forces. In flight, the actively morphing of bat wing includes the twisting from wing root to wing tip, the cambering along the chordwise direction, the bending along the spanwise direction and the wing area-changing caused by the stretch and retraction of the wingspan. It was found that the high thrust and lift required in bat flight are dependent on the wing twisting and cambering respectively. Moreover, the integrated wing-morphing generates the aerodynamic lift and thrust mainly during the downstroke and almost negligible forces during the upstroke. The wing area-changing and bending can be used to amplify the positive forces in the downstroke duration and reduce the negative forces in the upstroke duration
Bio-inspired long-based undulating fin propulsion is commonly employed in biological autonomous underwater vehicles (BAUVs), while the hydrodynamic characteristics of various undulating patterns are different. To investigate what kind of undulating pattern has outstanding propulsion or braking performance for BAUVs in directional maneuvers, undulations with four basic undulating patterns are numerically examined under the Open-source Field Operation And Manipulation environment at the Reynolds number of 5 × 102, 5 × 103, and 5 × 104, corresponding to viscous, transitional, and inertial flow regimes, respectively. The study is conducted at various non-dimensional phase speeds c (0.5–2.0, normalized by incoming flow speed) at a constant maximum amplitude of 0.08 and a wavelength of 0.5 (both are normalized by the fin cord length) to imitate the long-based fin. The numerical results indicate that the undulating fin motion with the amplitude envelope gradually increasing from the anterior part to the posterior (conical sinusoidal wave) part may be preferable for thrust generation; undulating with the amplitude envelope increasing from the anterior part to the mid part and decreasing toward the posterior (fusiform sinusoidal wave) presents the superior braking performance when the phase speed is low enough. Moreover, the influence of undulating patterns on the wake structure is analyzed. Through further comparative analysis for propulsion and braking performances, the results obtained here may have instructional significance to the propulsion mechanism in bionic design.
Many fish propel themselves using wave-like lateral flexion of their body and tail in the water. The undulatory body is driven by the distributed muscles, and locomotion is achieved by internal muscular stimulation and the external action of the fluid. As one of the material properties, the stiffness of the body being propelled plays an important role in the deformation process, especially for the muscle power input and phase lag. In this paper, a three-dimensional self-propelled elongated body model is employed to numerically investigate the effects of stiffness on the propulsion performance, including the forward speed, energy consumption, and energy-utilization ratio. According to various deformation characteristics and energy-utilization ratios, three deformation modes corresponding to high, medium, and low stiffness are identified. Our results indicate that a deforming body with medium stiffness has the highest efficiency, and its corresponding deformation is closest to that of fish in nature. When the stiffness of the fish body is higher than the normal level, more muscle energy is needed to sustain the tail beating of the same amplitude. A lower level of stiffness produces a more obvious phase lag in the fish body, which might lead to slow control responses. We also show that the stiffness of the fish body affects the scaling relationship between the swimming speed and the tail beating velocity. The upper and lower limits of the scaling exponent correspond to high and low levels of stiffness, respectively, and are also affected by the wavelength of the muscle contraction.
21 October 2014 in Applied Mathematics and Mechanics