Noise and distortion in real signals have posed challenges in signal detection in UHF RFID systems, with the exception of large frequency deviation. In this study, signal detection in a UHF RFID system was treated as a time series classification problem. The improved system was able to achieve frame synchronization detection and time-series data detection with a frequency deviation of 22%. The frame synchronization was based on the sequence detection with the most likely selection, and the data detection was performed using a symbol-by-symbol method with two-step adjustments in order to reduce time and hardware costs. The algorithm was mainly trained off-line using the experimental data, and then efficiently implemented in a UHF RFID system based on a software-defined radio platform. The experimental results showed that the learned detector had displayed improvements in detection accuracy and stability when compared to the existing method based on a correlation algorithm.
In this paper, we investigate the effects of negative bias instability (NBTI) and self-heating effect (SHE) on threshold voltage in NSFETs. To explore accurately the interaction between SHE and NBTI, we established an NBTI simulation framework based on trap microdynamics and considered the influence of the self-heating effect. The results show that NBTI weakens the SHE effect, while SHE exacerbates the NBTI effect. Since the width of the nanosheet in NSFET has a significant control effect on the electric field distribution, we also studied the effect of the width of the nanosheet on the NBTI and self-heating effect. The results show that increasing the width of the nanosheet will reduce the NBTI effect but will enhance the SHE effect. In addition, we extended our research to the SRAM cell circuit, and the results show that the NBTI effect will reduce the static noise margin (SNM) of the SRAM cell, and the NBTI effect affected by self-heating will make the SNM decrease more significantly. In addition, our research results also indicate that increasing the nanosheet width can help slow down the NBTI effect and the negative impact of NBTI on SRAM performance affected by the self-heating effect.
This brief presents a fully integrated automatic impedance-matching RF energy harvesting system that automatically compensates for variations at the antenna-rectifier interface. The control loop is fully integrated on-chip with a low-voltage, low-power design. The design is fabricated in 0.18-μm CMOS technology, and the active chip area is 0.064 mm2. The sensitivity optimized by impedance tuning can be improved to more than -30.5 dBm for 0.7 V output at varied initial mismatches, leading to a maximum increase in sensitivity of 5 dB. The control circuit's power consumption is only 2.4 nW, and the minimum supply voltage is 416 mV.
The high precision and low power consumption of the clock generator are critical in passive RFID transponders and passive IoT chips, but fluctuations in PVT can cause considerable degradation in the precision of the chip’s internal clocks. This paper proposes a high-precision clock circuit with a single-shot calibration method to addresses this issue in a low-power clock solution. Based on the reference timespan in the preamble of the down-link RF envelope, a TDIF (Time-digital to current-frequency) calibration method was implemented with both a streamlined procedure and customized circuits. By computing the difference between the time counts and applying it to an ultra-low-power, current-starved oscillator, the current change ratio can be linearly controlled. Compared to the traditional integer frequency division scheme used by passive tags for a 160 k bits up-link data rate, the required frequency for the clock generator was reduced from 960 kHz to 320 kHz, the calibration error was reduced from ±10% to ±3% for ±25% frequency deviation, the calibration time was 133.3 μs for a single shot in this work, and the power consumption was 158 nW after the calibration was completed. This leads to an excellent power efficiency of 0.59 nW/kHz and meets the requirements of low power, low cost, and PVT robustness in the RF-powered passive IoT chips. By appropriately increasing the number of calibration digits and the duration, this calibration approach could also be used for other ultra-low-power passive IoT chips that require higher-precision clocking without the use of off-chip crystals.
An effective codesign methodology of high sensitivity RF energy harvesting (RFEH) system for passive IoT applications is proposed, and chip implementation based on this solution was fabricated in standard TSMC 180 nm CMOS technology. By this systematic approach, a RFEH system including antenna, rectifier, power management unit (PMU) and impedance self-calibrate network were adopted to achieve an excellent sensitivity performance, which is characterized not only by high-Q factor but also large bandwidth. This work achieved high sensitivity performance of -32 dBm in 920~925 MHz for 0.7 V output voltage in anechoic chamber environment. Moreover, it can be powered by 36 dBm effective-isotropic radiated power source at a distance of 68 m outdoors.
1 April 2008 in 2008 IEEE International Symposium on Parallel and Distributed Processing
In this paper, we discuss a library generator for parallel sorting routines that examines the input characteristics (and the parameters they affect) to select the best performing algorithm. Our preliminary experimental results show that the automatic generation of a distributed memory parallel sorting routine provides up to a four fold improvement over standard parallel algorithms with typical parameters. With the recent importance of multicore processors, we are extending this work to shared memory. This provides new challenges specific to multicore systems. However, with their increasing popularity, this extension becomes very valuable.