Purpose: Structural health monitoring (SHM) has become an attractive subject in aerospace engineering field considering the opportunity to avoid catastrophic failures by detecting damage in advance and to reduce maintenance costs. Fibre Bragg Grating (FBG) sensors are denoted as one of the most promising sensors for SHM applications as they are lightweight, immune to electromagnetic effects and able to be embedded between the layers of composite structures. The purpose of this paper is to research on and demonstrate the feasibility of FBG sensors for SHM of composite structures. Design/methodology/approach: Applications on thin composite beams intended for SHM studies are presented. The sensor system, which includes FBG sensors and related interrogator system, and manufacturing of the beams with embedded sensors, are detailed. Static tension and torsion tests are conducted to verify the effectiveness of the system. Strain analysis results obtained from the tests are compared with the ones obtained from the finite element analyses conducted using ABAQUS® software. In addition, the comparison between the data obtained from the FBG sensors and from the strain gauges is made by also considering the noise content. Finally, fatigue test under torsion load is conducted to observe the durability of FBG sensors. Findings: The results demonstrated that FBG sensors are feasible for SHM of composite structures as the strain data are accurate and less noisy compared to that obtained from the strain gauges. Furthermore, the convenience of obtaining reliable data between the layers of a composite structure using embedded FBG sensors is observed. Practical implications: Observing the advantages of the FBG sensors for strain measurement will promote using FBG sensors for damage detection related to the SHM applications. Originality/value: This paper presents applications of FBG sensors on thin composite beams, which reveal the suitability of FBG sensors for SHM of lightweight composite structures.
In the field of aerospace engineering, the design and manufacturing of high aspect ratio composite wings has become a focal point of innovation and efficiency. These long, slender wings, constructed with advanced materials such as carbon fiber and employing efficient manufacturing methods such as vacuum bagging, hold the promise of significantly lighter aircraft, reduced fuel consumption, and enhanced overall performance. However, to fully realize these benefits, it is imperative to address a multitude of structural and aeroelastic constraints. This research presents a novel aeroelastically tailored Multi-objective, Multi-disciplinary Design Optimization (MMDO) approach that seamlessly integrates numerical optimization techniques to minimize weight and ensure structural integrity. The optimized wing configuration is then manufactured, and a Ground Vibration Test (GVT) and static deflection analysis using the Digital Image Correlation (DIC) system are used to validate and correlate with the numerical model. Within the fully automated in-house Nonlinear Aeroelastic Simulation Software (NAS2) package (version v1.0), the integration of analytical tools offers a robust numerical approach for enhancing aeroelastic and structural performance in the design of composite wings. Nonlinear aeroelastic analyses and tailoring are included, and a population-based stochastic optimization is used to determine the optimum design within NAS2. These analytical tools contribute to a comprehensive and efficient methodology for designing composite wings with improved aeroelastic and structural characteristics. This comprehensive methodology aims to produce composite wings that not only meet rigorous safety and performance standards but also drive cost-efficiency in the aerospace industry. Through this multidisciplinary approach, the authors seek to underscore the pivotal role of tailoring aeroelastic solutions in the advanced design and manufacturing of high aspect ratio composite wings, thereby contributing to the continued evolution of aerospace technology.
27 June 2011 in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
In this paper the performance of a piezoelectric sensor/actuator pair and self-sensing piezoelectric actuator on the investigation of vibration characteristics and active vibration control of a smart beam are presented. The performance of piezoelectric patches on actuation and sensing is evaluated by investigating the vibration characteristics of the smart beam via various excitation mechanisms and transduction systems. For active vibration suppression of the smart beam, robust controllers are designed and experimentally implemented by using a piezoelectric sensor/actuator pair and self-sensing piezoelectric actuator. Finally, experimental results for active control of free and the first-resonance forced vibration of the smart beam are presented.
The idea of morphing is drawing extensive attention in aerospace technologies. Several different approaches like span, camber, twist, and sweep are finding applications. In this work, the concept of a trailing edge control surface which is capable of performing decamber morphing is explained. The upper and lower parts of the control surface undergo different chordwise elongations and the difference between these displacements gives rise to either camber or decamber morphing. The necessary force is achieved by the help of servo actuators. During the design, the structural analyses were done to determine the best viable options for the number of servo actuators, the location of the servo actuators, and the material properties used in the control surface. The control surface was designed of aluminum, composite and compliant materials hence was called a hybrid one. The structural analyses were conducted by using ANSYS® Workbench v14.0 package program. After finding the best viable design, which was made for in vacuo condition, the proposed design was also verified under the simulated aerodynamic loading. The aerodynamic loads were obtained from CFD analyses which were done with SU2 V3.2.3 open-source flow solver.
Fibre Bragg Grating (FBG) sensors are frequently being used for Structural Health Monitoring (SHM) of aerospace structures. One of the most important advantages of using FBG sensors is that it is possible to embed them into composites. In this paper, manufacturing methods of composite specimens with embedded FBG sensors are given. To avoid stress concentrations at ingress/egress regions of fibre optic wires, PTFE (Teflon) tubes were used during manufacturing. Moreover, FBG connectors melt at high curing temperatures. Therefore, those connectors were cut and after manufacturing, these connectors were spliced back to the FBG sensors. Embedded FBG’s were then checked and the correct wavelength data were taken. All the sensors were observed as intact and ready for bending tests. Procedure for bending tests is also explained including applied loads, boundary conditions, test setup and the peripheral equipment. Results of bending tests show that the system is an appropriate one for SHM purposes.
1 December 2017 in Aerospace Science and Technology