Gerrit Olivier

Dr. Gerrit Olivier

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 April 2019 in Geophysical Research Letters
Verified
Journal Article
Open access
PDF file
GOGerrit Olivier
Gerrit Olivier
FBF. Brenguier
F. Brenguier
RCR. Carey
R. Carey
POP. Okubo
P. Okubo
CDC. Donaldson
C. Donaldson
The 2018 Kīlauea eruption was a complex event that included deformation and eruption at the summit and along the East Rift Zone. We use ambient seismic noise interferometry to measure time‐lapse changes in seismic velocity of the volcanic edifice prior to the lower East Rift Zone eruption. Our results show that seismic velocities increase in relation to gradual inflation of the edifice between 1 March and 20 April. In the 10 days prior to the 3rd of May eruption onset, a rapid seismic velocity decrease occurs even though the summit is still inflating. We confirm that intereruptive velocity change is correlated with surface deformation, while the velocity decrease prior to eruption is likely due to accumulating damage induced by the pressure exerted by the magma reservoir on the edifice. The accumulating damage and subsequent decrease in bulk edifice strength may have facilitated increased transport of magma from the summit reservoir to the Middle East Rift Zone.

15 July 2016 in Interpretation
Verified
Journal Article
Closed access
GOGerrit Olivier
Gerrit Olivier
FBFlorent Brenguier
Florent Brenguier
Recent results have shown that crosscorrelating ambient seismic noise recorded in underground mines can successfully extract the seismic Green’s function between sensors. We have revisited an earlier experiment that showed that these virtual seismic sources can be used to measure changes in seismic velocity accurately enough to monitor the short- and long-term influences of a blast in an underground mine. To use this method routinely, it is important to determine the cause of velocity variations in the absence of large dynamic stress perturbations (such as blasts). It also is important to calibrate the seismic velocity changes in terms of known stress changes so the effect of mining activities can be quantified in units that can be used by geotechnical engineers. To this end, we used coda-wave interferometry to measure relative velocity variations during times where no significant blasting or microseismic activity occurred and compared it to atmospheric air pressure changes, temperature variations, and modeled tidal strain. The results indicate that atmospheric air pressure changes have a measurable influence on the long-term seismic velocity variations at depth in the absence of large dynamic stress perturbations. This influence enabled us to determine the sensitivity of the relative velocity changes to stress, where a value of 3.2×10−6  %/Pa was found. This calibration essentially enables us to turn each sensor pair in an underground mine into a stress meter, paving the way for geotechnical engineers to use ambient seismic noise correlations to monitor the evolution of stress and to assess seismic hazard in conjunction with conventional microseismic methods.

1 November 2022 in Sensors
Verified
Journal Article
Open access
PDF file
GOGerrit Olivier
Gerrit Olivier
BBBraeden Borg
Braeden Borg
LTLawrence Trevor
Lawrence Trevor
BCBoris Combeau
Boris Combeau
PDPhilippe Dales
Philippe Dales
MPMatthew Pearson
Matthew Pearson
As most of the outcropping and shallow mineral deposits have been found, new technology is imperative to finding the hidden critical mineral deposits required to transition to renewable energy. One such new technique, called ambient seismic noise tomography, has shown promise in recent years as a low-cost, low environmental impact method that can image under cover and at depth. Wireless and compact nodal seismic technology has been instrumental to enable industry applications of ambient noise tomography, but these devices are designed for the active seismic reflection method and do not have the required sensitivity at low frequencies for ambient noise tomography, and real-time data transmission in remote locations requires significant infrastructure to be installed. In this paper, we show the development and testing of the Geode—a real-time seismic node purpose-built by Fleet Space Technologies for ambient seismic noise tomography on exploration scales. We discuss the key differences between current nodal technology and the Geode and show results of a field trial where the performance of the Geode is compared with a commercially popular nodal geophone. The use of a 2 Hz high sensitivity geophone and low noise digitiser results in an instrument noise floor that is more than 30 dB lower below 5 Hz than nodes that are commonly used in the industry. The increased sensitivity results in signal-to-noise ratios in the cross-correlation functions in the field trial that are more than double that of commercially available nodal geophone at low frequencies. When considering the full bandwidth of retrievable correlations in our study, using the Geode would reduce the required recording time from 75 h to 32 h to achieve an average signal-to-noise ratio in the cross-correlation functions of 10. We also discuss the integration of a real-time direct-to-satellite Internet of Things (DtS-IoT) modem in the Geode, which, together with edge processing of seismic data directly on the Geode, enables us to image the subsurface in real-time. During the field trial, the Geodes successfully transmitted more than 90% of the available preprocessed data packets. The Geode is compact enough so that several devices can be carried and installed by one field technician, whilst the array of stations do not require a base station to transmit data to the cloud for further processing. We believe this is the future of passive seismic surveys and will result in faster and more dynamic seismic imaging capabilities analogous to the medical imaging community, increasing the pace at which new mineral deposits are discovered.

1 September 2018 in Géotechnique Letters
Verified
Journal Article
Closed access
GOGerrit Olivier
Gerrit Olivier
TWT. de Wit
T. de Wit
FBF. Brenguier
F. Brenguier
LBL. Bezuidenhout
L. Bezuidenhout
TKT. Kunjwa
T. Kunjwa
Tailings storage facilities (TSFs) are some of the most challenging structures to operate in the mining industry. Some of these structures are susceptible to liquefaction and piping failure, and need to be monitored carefully. In this study, ambient seismic noise interferometry is applied to image the internal structure of a tailings storage facility (TSF) that showed signs of increased seepage. Twenty geophones were deployed along a roughly 100 m section of the TSF and recorded continuous seismic data. The ambient noise was used to create Love wave dispersion curves between sensor pairs, which were in turn inverted to estimate the shear wave velocity of the dam wall as a function of depth. The velocity profile indicated the phreatic surface roughly 10 m below the surface, with regions near the centre of the array showing the phreatic surface as close as 3 m below the surface. These areas are spatially well correlated with the area where increased seepage was identified and the results were comparable with cone penetration tests that were performed in the area. The study showed that the analysis of ambient seismic noise can be a cost-effective, fast and non-invasive method to image the internal structure of TSFs.

26 May 2021 in Seismological Research Letters
Verified
Journal Article
Closed access
PDF file
MGMartin Gal
Martin Gal
ELErnest Lotter
Ernest Lotter
GOGerrit Olivier
Gerrit Olivier
MGMark Green
Mark Green
SMStephen Meyer
Stephen Meyer
ARAnya M. Reading
Anya M. Reading
The amount of recorded seismic event data is rapidly growing, and manual processing by trained human experts to infer hypocenter, source parameters, and moment tensor solutions is therefore no longer feasible. Automated procedures are required to process data efficiently and include quality‐control measures that allow for outlier detection. We present a modular cross‐correlation location (CCLoc) algorithm for induced seismicity that uses cross correlations of either raw seismograms or characteristic functions derived from them followed by a reverse migration procedure. The novelty of this approach is the inclusion of cross pairs of P and S arrivals and the inclusion of autocorrelations, both of which add a distance constraint to the hypocenter estimation. The algorithm is modular in the sense that preprocessing can be tailored to specific data or task. Nine months of seismic data from an underground hard‐rock tin mine are processed in a fully automated mode using a machine‐learning approach for seismic phase arrival detection and using the estimated arrival functions as input for CCLoc. Making use of the average cross‐correlation value as a quality constraint, CCLoc can successfully infer source information on 92% of previously manually processed data. The accuracy of automatic processing is demonstrated by comparing hypocenter, source parameter, and moment tensor solutions between the two datasets. The algorithm will potentially aid the analysis of induced or other seismicity and is particularly well suited to use in the case of large numbers of seismic sensors recording many events.

4 November 2017 in Geophysical Research Letters
Verified
Journal Article
Closed access
PDF file
PDPhilippe Dales
Philippe Dales
PAPascal Audet
Pascal Audet
GOGerrit Olivier
Gerrit Olivier