Crystal facet engineering is one of the most important ways to enhance the photoactivity of photocatalysts, but it remains challenging so far. In addition, the effects of exposed facets and crystallite sizes on the photoactivity of BiOX (X = Cl, Br, or I) nanosheets have been widely investigated. However, it is still unclear which one between the exposed facets and the crystallite sizes is more important for the photoactivity of the BiOX nanosheets. In this work, a series of BiOBr nanosheets with tunable exposed facets and crystallite sizes were solvothermally synthesized in a mixed solvent of n-propanol, water, and acetic acid. The regulation of the exposed facets and crystallite sizes was achieved simply by changing the n-propanol/water volume ratios (Rp/w, 0/30 to 30/0) of the mixed solvent. At low n-propanol contents (Rp/w < 15/15), the obtained BiOBr nanosheets expose dominantly (001) facets, while at high n-propanol contents (Rp/w > 20/10), they expose dominantly (010) facets. With increasing Rp/w, the lateral size and thickness of the BiOBr nanosheets all decrease, from 1700 to 174 nm and from 156 to 17 nm, respectively. The effects of exposed facets and thicknesses of BiOBr nanosheets on the photocatalytic activity, evaluated by degradation of salicylic acid and rhodamine B under visible-light irradiation, were investigated. The exposed facet and thickness of BiOBr nanosheets are both important for their photocatalytic performance. The (001) facets exhibit a higher photocatalytic activity than the (010) facets. For the BiOBr nanosheets with the same (001) or (010) exposed facets, the photocatalytic activity increases with a decrease in their thickness. This study provides a new facile way to adjust the exposed facets and crystallite sizes of BiOX, and the findings may provide guidance for crystal facet engineering of other photocatalysts.
MnII-doped g-C3N4obtained through redox reactions between a permanganate and urea upon calcination in an inert gas exhibits enhanced photogenerated charge carrier separation.
Nanocomposite (NC) hydrogels of positively charged layered double hydroxide (LDH) single-layer nanosheet (SLNS) cross-linked poly(N-isopropylacrylamide) (PNIPAM) were synthesized. Especially, the LDH SLNSs used here were pre-synthesized via an aqueous synthetic route without using organic solvents and modifiers. The obtained LDH/PNIPAM NC hydrogels were characterized using XRD, SEM, TEM, and DSC. The mechanical and thermoresponsive properties were determined using tensile, compression, and swelling/deswelling tests. Interestingly, different network structures are observed for the NC hydrogels along the horizontal and vertical directions; those along the horizontal direction exhibit a fine and uniform sponge-like network structure while those along the vertical direction exhibit a hierarchical layered architecture. Compared with the conventional N,N′-methylene bisacrylamide cross-linked PNIPAM hydrogel, the NC hydrogels exhibit extraordinary deformability and stretchability and obviously improved thermoresponsive swelling/deswelling characteristics. Furthermore, the fracture elongation observed here is obviously higher than those reported for negatively charged clay/PNIPAM NC hydrogels. With the increase in the LDH content from 0.8 to 2.0 wt%, the fracture strength and the compressive strength at an 85% strain increase from 23.5 to 37.2 kPa and from 0.15 to 0.57 MPa, respectively, while the fracture elongation decreases from 2689 to 2202%. The mechanism for the improved mechanical performances of the NC hydrogels is discussed. To the best of our knowledge, this is the first report on LDH/PNIPAM hydrogels. This work provides a green synthesis route for LDH-containing NC hydrogels. The new NC hydrogels may have great potential applications such as in tissue engineering, drug vehicles, and sorbents.
1 July 2019 in Journal of Colloid and Interface Science