Geng Chen

Dr. Geng Chen


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
YZYifan Zhou
Yifan Zhou
YZYingying Zhu
Yingying Zhu
JZjinyuan zhu
jinyuan zhu
CLChaoran Li
Chaoran Li
GCGeng Chen
Geng Chen
Discharging large amounts of domestic and industrial wastewater drastically increases the reactive nitrogen content in aquatic ecosystems, which causes severe ecological stress and biodiversity loss. This paper reviews three common types of denitrification processes, including physical, chemical, and biological processes, and mainly focuses on the membrane technology for nitrogen recovery. The applicable conditions and effects of various treatment methods, as well as the advantages, disadvantages, and influencing factors of membrane technologies, are summarized. Finally, it is proposed that developing effective combinations of different treatment methods and researching new processes with high efficiency, economy, and energy savings, such as microbial fuel cells and anaerobic osmotic membrane bioreactors, are the research and development directions of wastewater treatment processes.

YXYang Xu
Yang Xu
YZYingying Zhu
Yingying Zhu
ZCZhen Chen
Zhen Chen
JZjinyuan zhu
jinyuan zhu
GCGeng Chen
Geng Chen
Forward osmosis (FO) is an evolving membrane separation technology for water treatment and reclamation. However, FO water treatment technology is limited by factors such as concentration polarization, membrane fouling, and reverse solute flux. Therefore, it is of a great importance to prepare an efficient high-density porous membrane and to select an appropriate draw solute to reduce concentration polarization, membrane fouling, and reverse solute flux. This review aims to present a thorough evaluation of the advancement of different draw solutes and membranes with their effects on FO performance. NaCl is still widely used in a large number of studies, and several general draw solutes, such as organic-based and inorganic-based, are selected based on their osmotic pressure and water solubility. The selection criteria for reusable solutes, such as heat-recovered gaseous draw, magnetic field-recovered MNPs, and electrically or thermally-responsive hydrogel are primarily based on their industrial efficiency and energy requirements. CA membranes are resistant to chlorine degradation and are hydrophilic, while TFC/TFN exhibit a high inhibition of bio-adhesion and hydrolysis. AQPs are emerging membranes, due to proteins with complete retention capacity. Moreover, the development of the hybrid system combining FO with other energy or water treatment technologies is crucial to the sustainability of FO.

4 March 2022 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
YXYang Xu
Yang Xu
YZYingying Zhu
Yingying Zhu
PSPengfei Shen
Pengfei Shen
GCGeng Chen
Geng Chen
XLXinbao Li
Xinbao Li

2 July 2023 in Molecules
Verified
Journal Article
Open access
PDF file
JZjinyuan zhu
jinyuan zhu
YZYingying Zhu
Yingying Zhu
YZYifan Zhou
Yifan Zhou
CWChen Wu
Chen Wu
ZCZhen Chen
Zhen Chen
GCGeng Chen
Geng Chen
The direct or indirect discharge of organic pollutants causes serious environmental problems and endangers human health. The high electron–hole recombination rate greatly limits the catalytic efficiency of traditional TiO2-based catalysts. Therefore, starting from low-cost activated carbon (AC), a photocatalyst (F-Si-TiO2/AC) comprising fluorine (F)- and silicon (Si)-doped TiO2 loaded on AC has been developed. F-Si-TiO2/AC has a porous structure. TiO2 nanoparticles were uniformly fixed on the surface or pores of AC, producing many catalytic sites. The band gap of F-Si-TiO2/AC is only 2.7 eV. In addition, F-Si-TiO2/AC exhibits an excellent adsorption capacity toward methyl orange (MO) (57%) in the dark after 60 min. Under the optimal preparation conditions, F-Si-TiO2/AC showed a significant photodegradation performance toward MO, reaching 97.7% after irradiation with visible light for 70 min. Even under the action of different anions and cations, its degradation efficiency is the lowest, at 64.0%, which has good prospects for practical application. At the same time, F-Si-TiO2/AC has long-term, stable, practical application potential and can be easily recovered from the solution. Therefore, this work provides new insights for the fabrication of low-cost, porous, activated, carbon-based photocatalysts, which can be used as high-performance photocatalysts for the degradation of organic pollutants.

22 November 2023 in ACS Applied Polymer Materials
Verified
Journal Article
Closed access
YZYingying Zhu
Yingying Zhu
YXYang Xu
Yang Xu
SCSiqi Chen
Siqi Chen
YZYifan Zhou
Yifan Zhou
JZJinyuan Zhu
Jinyuan Zhu
GCGeng Chen
Geng Chen

20 December 2023 in Molecules
Verified
Journal Article
Open access
PDF file
JLJianbin Luo
Jianbin Luo
XZXinbo Zhu
Xinbo Zhu
ZZZhiwei Zhong
Zhiwei Zhong
GCGeng Chen
Geng Chen
YHYu Hong
Yu Hong
ZZZijian Zhou
Zijian Zhou
A series of Co-M (M = Fe, Cr, and Mn) catalysts were synthesized by the sol-gel method for soot oxidation in a loose contact mode. The Co-Fe catalyst exhibited the best catalytic activity among the tested samples, with the characteristic temperatures (T10, T50, and T90) of 470 °C, 557 °C, and 602 °C, respectively, which were 57 °C, 51 °C, and 51 °C lower than those of the CoOx catalyst. Catalyst characterizations of N2 adsorption–desorption, X-ray diffraction (XRD), X-ray photo-electron spectrometry (XPS), and the temperature programmed desorption of O2 (O2-TPD) were performed to gain insights into the relationships between the activity of catalytic soot oxidation and the catalyst properties. The content of Co2+ (68.6%) increased due to the interactions between Co and Fe, while the redox properties and the relative concentration of surface oxygen adsorption (51.7%) were all improved, which could significantly boost the activity of catalytic soot oxidation. The effects of NO and contact mode on soot oxidation were investigated over the Co-Fe catalyst. The addition of 1000 ppm of NO led to significant reductions in T10, T50, and T90 by 92 °C, 106 °C, and 104 °C, respectively, compared to the case without the NO addition. In the tight contact mode, the soot oxidation was accelerated over the Co-Fe catalyst, resulting in 46 °C, 50 °C, and 50 °C reductions in T10, T50, and T90 compared to the loose contact mode. The comparison between real soot and model Printex-U showed that the T50 value of real soot (455 °C) was 102 °C lower than the model Printex-U soot.