This article analyzes the fundamental question of the mechanical properties representation in penetration analysis and its effect on the calculated results. Penetration analysis into a concrete target with a specified uniaxial compressive strength was carried out using different material models appearing in software libraries. These models determine the specific material equation of state and shear strength envelope related to the concrete uniaxial compressive strength. Different results were obtained for the same concrete strength. This proves that the unconfined compressive strength is not the governing parameter which determines the projectile penetration characteristics and that a large variation of results is obtained from different models. Analysis was then carried out on a case with documented constitutive properties of a concrete target that was penetrated by an instrumented projectile. The predicted penetration depth and the projectile deceleration time history were compared with the measured data, and very good correspondence was obtained. This proved that the specific properties of the penetrated medium should be incorporated in the analysis to properly predict the penetration event. The study then examined the commonly used approximation of a linearized equation of state and a linear Mohr–Coulomb model, replacing the true non-linear equations of state and the true non-linear shear strength dependence, and the linearized relationships’ effect on the analyzed results was assessed. A detailed study of the solution sensitivity to different parameters of the Mohr–Coulomb relationship then followed, and its effect on different penetration parameters (nose embedment duration, nose embedment velocity, penetration depth, peak deceleration, quasi-static deceleration) has been examined, to demonstrate how a perturbation in assumed concrete properties affects the solution of the penetration problem. The article illuminates the role of the constitutive equations on penetration analysis and the importance of the proper selection of the representative expressions and of their approximations.
19 September 2013 in International Journal for Numerical and Analytical Methods in Geomechanics
The paper presents an investigation on the response of a buried structure in a soft soil layer above a rock bed that is subjected to blast loading. A comprehensive approach to simulate the behavior of soft soil with a buried structure laying over a rock mass due to the dynamic (explosive) action in the rock mass is presented. The numerical algorithm was developed to simulate the shock wave propagation within the medium, considering both the bulk and deviatoric damage and taking into account the possible shear damage accumulation. It takes into account the contact conditions between the layers to simulate the shock wave transmission and the soil-structure interaction including their possible separation. The soil-lining interaction problem is solved by a combination of the variational-difference method (for the lining) and of the Godunov's method (for the soil). The coupling of these two approaches is performed by calculation of the contact stresses and velocities on the soil-lining boundary. Two types of the soil models were investigated – an ideal elastic plastic medium and an irreversible compressible medium with failure in bulk tension – and the results were compared with each other. The analysis of the free surface and interface velocities and displacements as well as the contact stresses and the damage at the media interface were carried out. The effects of the relative cover thickness on the interface and free surface behavior is studied. Analysis of the contact stresses at the soil-tunnel interface, was carried out. The effect of the charge location as well as the effect of the soil-rock interface on the tunnel's response was investigated.
21 April 2009 in International Journal for Numerical Methods in Engineering
This study focuses on a RC building with flat slabs that were designed according to current standards. A scenario of a slab with failed connections that is detached from its supporting columns and is falling downward is considered, and the impact results with the slab underneath are assessed. The suitability of the standards design criteria to provide safe design against impact loading is evaluated. It was found that larger span slabs experience heavier damage. Falling from a floor height and from a quarter floor height are analyzed and the damage results of these impacts are examined. At the lower impact velocity, the concrete slab surrounding the column undergoes major damage and shear deformations; In the case of a relatively short span slab, the rebars undergo large plastic deformations and almost reach the ultimate strain, such that a slightly higher impact velocity would cause rebars fracture and total failure of the slab-column connection. In the case of high impact velocity, the concrete in the slab around the column is fully crashed and the longitudinal and the bent up rebars are ruptured. The yield of the rebars occurs within a few milliseconds. During this extremely short time the impacted slab hardly starts developing its downward displacement. The impacted slab responds like a rigid body with severe damage concentration at the slab-column connection region. Different parameters affecting the slabs dynamic response are examined, and new insight is gained on the complex impact response of flat RC slabs. This study finds that the current design standards that are based on static loading considerations do not provide resilience to flat slab connections that are subjected to impact loading and therefore cannot prevent a progressive collapse scenario.