The research in this paper is related to the accuracy of the tilt compensation function of the GNSS/IMU receivers, which were examined in an open sky environment. The purpose of the paper is to point out to geodesists the conditions and limitations of using GNSS/IMU technology in precise measurements to not jeopardize the coordinate’s accuracy. The environment in which the measurement is made affects the quality of the GNSS signal and can limit the visibility of the satellite, leading to larger errors in the measurement. In this experiment, the current performance of the GNSS/IMU receivers was checked. Seven GNSS/IMU receivers were used for the realization of the experiment. For six receivers the compensation angle was α = 30°, while for one receiver, the compensation angle was α = 45°. The standard uncertainty of GNSS coordinates of the antenna phase center has values less than 9 mm. The standard uncertainty of the IMU component has values less than 31 mm. The measurement uncertainty of the position of the used GNSS receivers is in the range of 18.1 mm to 31.7 mm. The limit values for the differences along the coordinate axes x and y were determined, and their values are from 26 mm to 44 mm. In the conducted experiment, it was confirmed that three GNSS/IMU receivers have a “Satisfactory” result. The results show that GNSS/IMU measurements with a slope greater than 30° significantly affect the accuracy and reliability of GNSS/IMU technology. A slope greater than 45° has a deviation along the coordinate axes of 121.3 mm. The conducted research is particularly important for geodetic works that require high positioning performance. The testing method of the GNSS/IMU receiver presented in this paper can help its users to make correct conclusions regarding the coordinate accuracy of the measured point of interest.

The use of the GNSS devices in the RTK mode involves taking a vertical position using a circular spirit vial bubble located on the rod. Since the market of geodetic instruments, accessories and software is growing, the authors of this paper performed...

The validity of the results obtained within different permanent GNSS reference station networks (GNSS Network) must be periodically controlled using criteria that are generally known from statistical analyzes or prescribed by International Standards. Procedures for evaluating the uncertainty of measurements are defined in accordance with the purpose of the GNSS Network. The authors of this paper want to point out the need to establish requirements for periodical and systematical control of GNSS coordinates within the same permanent GNSS Network and control of GNSS coordinates between different permanent GNSS Networks measured on the same/unique point on the ground. This paper presents control procedures for three permanent GNSS reference station Networks established and operating in the Republic of Serbia. Special attention is on the analysis of data consistency within one permanent GNSS Network and the mutual consistency of GNSS data between different networks. The paper aims to promote reliance on the different GNSS Networks and contains suggestions on how GNSS Networks may prove that they are performing competently and that they can provide valid results for field measurements. Particularly highlighted is the need to plan and implement measures related to increasing the effectiveness of the GNSS system, achieving improved results, and preventing negative effects while performing field measurements. The paper presents the results for comparison, selected according to the rules for creating a Digital Cadastral Map features, i.e., points, lines, and polygon. The results for comparing point features are the GNSS coordinates. The results for comparing line features are the lengths of the line, i.e., distances, and the results for comparing polygon features are the areas of the polygons.

A theoretical model for porous viscoelastoplastic (VEP) materials in the dry state is investigated in this research study. The model is based on the principles of conservation of mass and energy using the rheological dynamic theory (RDT). The model provides expressions for the creep coefficient, Poisson’s ratio, modulus of elasticity, damage variable, and strength as a function of porosity and/or void volume fraction (VVF). The reliability of the proposed model was analyzed by comparing numerical results with experimental ones on hardened concrete. A numerical model was created and analyzed in the commercial software Abaqus and validated by comparison with experimental data obtained by geodetic measurements on a composite wood–lightweight concrete girder. The deflections and stresses of the beam resulting from the influence of concrete creep and porosity were analyzed at the initial moment of time and after 6 years. The results showed that the RDT provided a reliable model for estimating parameters after exposure to long-term loads.