In order to simulate the flow behavior and microstructure evolution during the pass interval period of the multi-pass deformation process, models of static recovery (SR) and static recrystallization (SRX) by the cellular automaton (CA) method for the 7055 aluminum alloy were established. Double-pass hot compression tests were conducted to acquire flow stress and microstructure variation during the pass interval period. With the basis of the material constants obtained from the compression tests, models of the SR, incubation period, nucleation rate and grain growth were fitted by least square method. A model of the grain topology and a statistical computation of the CA results were also introduced. The effects of the pass interval time, temperature, strain, strain rate and initial grain size on the microstructure variation for the SRX of the 7055 aluminum alloy were studied. The results show that a long pass interval time, large strain, high temperature and large strain rate are beneficial for finer grains during the pass interval period. The stable size of the static recrystallized grain is not concerned with the initial grain size, but mainly depends on the strain rate and temperature. The SRX plays a vital role in grain refinement, while the SR has no effect on the variation of microstructure morphology. Using flow stress and microstructure comparisons of the simulated and experimental CA results, the established CA models can accurately predict the flow stress and microstructure evolution during the pass interval period, and provide guidance for the selection of optimized parameters for the multi-pass deformation process.

Asymmetrical shear rolling with velocity asymmetry and geometry asymmetry is beneficial to enlarge deformation and refine grain size at the center of the thick plate compared to conventional symmetrical rolling. Dynamic recrystallization (DRX) plays a vital role in grain refinement during hot deformation. Finite element models (FEM) coupled with microstructure evolution models and cellular automata models (CA) are established to study the microstructure evolution of plate during asymmetrical shear rolling. The results show that a larger DRX fraction and a smaller average grain size can be obtained at the lower layer of the plate. The DRX fraction at the lower part increases with the ascending speed ratio, while that at upper part decreases. With the increase of the offset distance, the DRX fraction slightly decreases for the whole thickness of the plate. The differences in the DRX fraction and average grain size between the upper and lower surfaces increase with the ascending speed ratio; however, it varies little with the change of the speed ratio. Experiments are conducted and the CA models have a higher accuracy than FEM models as the grain morphology, DRX nuclei, and grain growth are taken into consideration in CA models, which are more similar to the actual DRX process during hot deformation.

To investigate the effect of quenching rate on microstructure, residual stress (RS) and mechanical properties of a rare-earth wrought magnesium alloy Mg-Gd-Y-Zr-Ag-Er, RS in 20 °C water quenching (WQ (20 °C)), 100 °C water quenching (WQ (100 °C)) or air cooling (AC) conditions were measured and compared with the simulation results, corresponding mechanical properties and microstructure in quenching and aging state were studied. The decrease of quenching rate has little effect on the grain size but makes the twinning disappear, precipitates increase and the texture weakened, leading to easier brittle fracture after aging. WQ (100 °C) is the best quenching condition in this study, with a significant decline in RS and only 4.9% and 3.7% decrease in yield stress (YS) and hardness compared with WQ (20 °C). The results make it feasible to invent an appropriate quenching method of greatly reducing RS while maintaining mechanical properties. The research conclusions would be beneficial to the application of the alloy.

Regulation of residual stress in a component is the key to improving its service performance. A cold expansion method was proposed for reducing the residual stress in 7050 aluminium alloy curved frame forging after quenching. The effect of the cold expansion method on the residual stress and equivalent plastic strain distribution of the 7050 aluminium alloy curved frame forging was investigated. The results showed that the maximum residual stress at the center thickness was reduced from 153 MPa to 94 MPa after the cold expansion, while it decreased from 283 MPa to 120 MPa at the surface with the highest stress reduction rate of 86.2%. The stress uniformity in the final forming region of the forging was improved. The equivalent plastic strain of the forging gradually decreases from the center to each side along the diameter of the expanded hole in cold expansion. The stress reduction effect matched with the distribution of equivalent plastic strain. The surface stress of the forging measured by x-rays diffraction (XRD) method was in agreement with the simulation results, and the reliability of the numerical model was verified. The cold expansion method can effectively reduce the quenched residual stress in curved frame forging.