The Internet of Things (IoT) is experiencing rapid growth and being adopted across multiple domains. For example, in industry it supports the connectivity needed to integrate smart machines, components and products in the ongoing Industry 4.0 trend. However, there is a myriad of communication technologies that complicate the needed integration, requiring gateways to connect to the Internet. Conversely, using IEEE 802.11 (WiFi) devices can connect to existing WiFi infrastructures directly and access the Internet with shorter communication delays and lower system cost. However, WiFi is energy consuming, impacting autonomy of the end devices. In this work we characterize a recent WiFi-enabled device, namely the ESP8266 module, that is low cost and branded as ultra-low-power, but whose performance for IoT applications is still undocumented. We explore the built-in sleep modes and we measure the impact of infrastructure parameters beacon interval and DTIM period on energy consumption, as well as packet delivery ratio and received signal strength as a function of distance and module antenna orientation to assert area coverage. The ESP8266 module showed suitability for battery powered IoT applications that allow 2-4 days recharge cycles on a 1000mAh battery with seconds-scale transmission intervals.
Interest on using mobile autonomous agents has been growing, recently, due to their capacity to cooperate for diverse purposes, from rescue to demining and security. However, such cooperation requires the exchange of state data that is time sensitive while achieving timeliness with RF communication is intrinsically difficult due to the openess of the medium. This paper describes a communication layer that improves the timeliness of periodic data exchanges among the team reducing the chances of lost packets caused by collisions between team members. In particular, the paper extends a previous proposal for an adaptive TDMA protocol with new self-configuration capabilities according to the current number of active team members. This feature further reduces the likelyhood of collisions within the team. Several experimental results with an actual system implementation show the effectiveness of the proposed solution.
Due to multiple reasons, emergency wards can become overloaded with patients, some of which can be in critical health conditions. To improve the emergency service and avoid deaths and serious adverse events that could be potentially prevented, it is mandatory to do a continuous monitoring of patients physiological parameters. This is a good fit for Internet of Things (IoT) technology, but the scenario imposes hard constraints on autonomy, connectivity, interoperability, and delay. In this paper, we propose a full Internet-based architecture using open protocols from the wearable sensors up to the monitoring system. Particularly, we use low-cost and low-power WiFi-enabled wearable physiological sensors that connect directly to the Internet infrastructure and run open communication protocols, namely, oneM2M. At the upper end, our architecture relies on openEHR for data semantics, storage, and monitoring. Overall, we show the feasibility of our open IoT architecture exhibiting 20–50 ms end-to-end latency and 30–50 h sensor autonomy at a fraction of the cost of current non-interoperable vertical solutions.
Vehicular ad-hoc networks (VANET) enable vehicles to exchange information on traffic conditions, dynamic status and localization, to enhance road safety and transportation efficiency. A typical VANET application is platooning, which can take advantage of exchanging information on speed, heading and position to allow shorter inter-vehicle distances without compromising safety. However, the platooning performance depends drastically on the quality of the communication channel, which in turn is highly influenced by the medium access control protocol (MAC). Currently, VANETs use the IEEE 802.11p MAC, which follows a carrier sense multiple access with collision avoidance (CSMA/CA) policy that is prone to collisions and degrades significantly with network load. This has led to recent proposals for a time-division multiple access (TDMA)-based MAC that synchronize vehicles’ beacons to prevent or reduce collisions. In this paper, we take CSMA/CA and two TDMA-based overlay protocols, i.e., deployed over CSMA/CA, namely PLEXE-slotted and RA-TDMAp, and carry out extensive simulations with varying platoon sizes, number of occupied lanes and transmit power to deduce empirical models that provide estimates of average number of collisions per second and average busy time ratio. In particular, we show that these estimates can be obtained from observing the number of radio-frequency (RF) neighbours, i.e., number of distinct sources of the packets received by each vehicle per time unit. These estimates can enhance the online adaptation of distributed applications, particularly platooning control, to varying conditions of the communication channel.