İSMAİL HAKKI TARHAN

Dr. İSMAİL HAKKI TARHAN

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 December 2024 in Buildings
Verified
Journal Article
Open access
PDF file
YTYeşim Tarhan
Yeşim Tarhan
İTİSMAİL HAKKI TARHAN
İSMAİL HAKKI TARHAN
Remzi ŞahinRemzi Şahin
Remzi Şahin
Three-dimensional printing technology is transforming the construction industry, which is increasingly turning to advanced materials and techniques to meet environmental and economic challenges. This comprehensive literature review evaluated various binder materials, including cement, geopolymers, earthen materials, supplementary cementitious materials, polymers, and biopolymers, with a focus on their environmental impacts and rheological properties. The study revealed an increasing interest in cementitious binders, which deliver essential structural strength and exhibit a wide range of yield stress values (15 to 6500 Pa), influenced by binder type and supplementary materials such as nanoclay. However, the significant CO2 emissions associated with cement pose major sustainability challenges. As a sustainable alternative, geopolymers demonstrate lower yield stress values (800 to 3000 Pa) while ensuring adequate buildability for vertical printing and reducing environmental impact. These findings underscore the need to adopt sustainable binder matrices to align 3D printing construction practices with global sustainability goals.

5 June 2023 in Engineering Failure Analysis
Verified
Journal Article
Closed access
İTİSMAİL HAKKI TARHAN
İSMAİL HAKKI TARHAN
HUHabib Uysal
Habib Uysal

23 December 2024 in Earthquake Engineering & Structural Dynamics
Verified
Journal Article
Closed access
İTİSMAİL HAKKI TARHAN
İSMAİL HAKKI TARHAN
Nathanael SavalleNathanael Savalle
Nathanael Savalle
HUHabib Uysal
Habib Uysal
Luis Carlos Martins da SilvaLuis Carlos Martins da Silva
Luis Carlos Martins da Silva
PLPaulo B. Lourenço
Paulo B. Lourenço


9 May 2021
Verified
Book Chapter
Closed access
PDF file
YTYeşim Tarhan
Yeşim Tarhan
İTİSMAİL HAKKI TARHAN
İSMAİL HAKKI TARHAN
FCFlávio Craveiro
Flávio Craveiro
HBHelena Bártolo
Helena Bártolo

24 June 2025 in Challenge Journal of Structural Mechanics
Verified
Journal Article
Open access
YTYeşim Tarhan
Yeşim Tarhan
İTİSMAİL HAKKI TARHAN
İSMAİL HAKKI TARHAN
APArnaud Perrot
Arnaud Perrot
3D printing technology has transformed the construction industry by enabling rapid and cost-effective production of complex geometries. However, it faces significant challenges, including sustainability concerns due to cement's environmental impact and reinforcement issues arising from the incompatibility of traditional steel. These challenges necessitate the development of innovative material solutions. This study aims to enhance the bond strength between sustainable earth-based mortar and jute fibers used as reinforcement in 3D printed structures by exploring the effects of different treatments and compositions. Bond strength was evaluated by considering the effect of different treatments on the resistance of the fiber to being pulled out of the mortar. Pull-out tests were conducted on specimens with varying compositions and treatments. Results demonstrated substantial improvement in bond performance; specifically, the reference sand-free earth-clay mortar exhibited the lowest interfacial shear strength of 0.30 MPa. The most remarkable enhancement was observed in specimen which jute fibers pre-treated by immersion in mud slurry, which showed a 147% increase, reaching an interfacial shear strength of 0.74 MPa. Combining sand addition and fiber pre-treatment, however, did not yield additional benefits. These results indicate that simple, cost-effective local treatments can notably enhance fiber-matrix bond strength in 3D-printed earth-based structures without necessitating additional equipment or significant expense.