Andrew Thomson

Dr. Andrew Thomson


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 July 2011 in Progress in Photovoltaics: Research and Applications
Verified
Journal Article
Closed access
PDF file
ATAndrew Thomson
Andrew Thomson
KMKeith R. McIntosh
Keith R. McIntosh

1 January 2013 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
YWYimao Wan
Yimao Wan
KMKeith R. McIntosh
Keith R. McIntosh
ATAndrew Thomson
Andrew Thomson
ACAndres Cuevas
Andres Cuevas
We demonstrate that nearly stoichiometric amorphous silicon nitride (SiN x) can exhibit excellent surface passivation on both p- and n -type c-Si, as well as low absorption at short wavelengths. The key process to obtain such a SiN x is the optimized deposition pressure. The effective carrier lifetimes of these samples exceed the commonly accepted intrinsic upper limit over a wide range of excess carrier densities. We achieve a low Seff,UL of 1.6 cm/s on 0.85-Ω·cm p -type and immeasurably low Seff,UL on 0.47-Ω·cm n-type silicon passivated by the SiN x deposited at 290°C. Capacitance-voltage (C-V) measurements reveal that this SiNx has a density of interface states of 3.0 × 1011 eV-1cm-2 at midgap and an insulator charge of 5.6 × 1011 cm-2. By comparing the measured injection-dependent Seff,UL with calculated Seff,UL by an extended Shockley-Read-Hall (SRH) model, we conclude that either Defect A or B (or both) observed by Schmidt is likely to dominate the surface recombination at our Si-SiNx interface. In addition to the outstanding surface passivation, this SiN x has a low absorption coefficient at short wavelengths. Compared with Si-rich SiNx of an equivalent passivation, the optimized SiN x would enhance the photogenerated current density by more than 0.66 mA/cm2or 1.40 mA/cm2 for solar cells encapsulated in glass/ethylene-vinyl acetate or operating in air, respectively. The SiNx described here is ideally suited for high-efficiency solar cells, which require good surface passivation and low absorption from their front surface coatings.

11 April 2018 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
JQJiadong Qian
Jiadong Qian
ATAndrew Thomson
Andrew Thomson
Andrew BlakersAndrew Blakers
Andrew Blakers
Marco ErnstMarco Ernst
Marco Ernst
The impact of partial shading on cell operating current, voltage, and temperature is simulated, for a half-cell module with series–parallel–series connections and for the conventional full-cell module. When shaded, we find the half-cell modules comprising two parallel 60-half-cell strings benefit from a reduced heat dissipation compared to a 60-full-cell series connected design. The maximum hotspot cell temperature of the shaded half-cell module is 28 °C lower than that of the full-cell module. Our result suggests that half-cell module design could mitigate hotspot degradation or failure in crystalline-silicon photovoltaic modules.

21 July 2011 in Progress in Photovoltaics: Research and Applications
Verified
Journal Article
Closed access
PDF file
JBJérémy Barbé
Jérémy Barbé
ATAndrew Thomson
Andrew Thomson
EWEr‐Chien Wang
Er‐Chien Wang
KMKeith McIntosh
Keith McIntosh
KCKylie Catchpole
Kylie Catchpole

1 January 2013 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
XZXinyu Zhang
Xinyu Zhang
ACAndres Cuevas
Andres Cuevas
ATAndrew Thomson
Andrew Thomson
In this paper, we investigate the relationship between the deposition-process parameters of reactively sputtered aluminium oxide films and the passivation of silicon surfaces. A method of tuning the deposition process has been established that results in a reduced level of surface recombination, where surface recombination velocities as low as 8.5 cm/s have been achieved on 1 Ω·cm n-type monocrystalline silicon. We find that in order to achieve good surface passivation, the deposition need to be conducted at low power density and at high deposition pressure. We have found that effective passivation is achieved when a sputtering target is close to being fully oxidized-indicated by deposition rate - likely resulting in films that are less aluminium rich. Additionally, Fourier-transform-infrared spectroscopy measurements were used for film characterization; the correlation between effective lifetime and the integrated absorption of all Al and O related bonds shows that films with lower absorption in the wavenumber range 500-1060 cm-1 result in better passivation.

1 August 2018 in Solar Energy Materials and Solar Cells
Verified
Journal Article
Closed access
IHIngrid Haedrich
Ingrid Haedrich
Marco ErnstMarco Ernst
Marco Ernst
ATAndrew Thomson
Andrew Thomson
PZPeiting Zheng
Peiting Zheng
XZXinyu Zhang
Xinyu Zhang
DMDaniel Macdonald
Daniel Macdonald