A frequency-modulated continuous-wave (FMCW) radar takes advantage of stretch processing (dechirping, deramping) to reduce the sampling requirements of radar systems such as automotive radars. When applying phase coding into FMCW radar systems for interference mitigation or joint communication, preservation of this benefit is not possible, due to the nature of this process. This paper proposes a new phase coded FMCW system as well as a processing strategy based on a group-delay filter to deal with unaligned phase-coded radar return signals. Moreover, this paper proposes an improved interference mitigation method based on a phase-coded linear- frequency-modulated (LFM) continuous waveform and points out the improvements in the signal-to-interference ratio (SIR). In the proposed mitigation technique, unlike the traditional approach where RF spectrum spreads, the beat frequency spectrum of the FMCW radar spreads, thus the bandwidth of RF hardware stays the same as a classical LFM continuous wave radar. The success of the proposed phase coded frequency-modulated continuous-wave (PC-FMCW) radar is illustrated in simulations and increased interference mitigation performance is validated by experiments.
This paper presents a new approach to mitigating radar interference and focuses on the application of automotive radar. Traditional interference mitigation techniques in automotive radar depend on detection and identification of the interference. With this paper, we propose a novel method based on advanced signal separation techniques which do not need any prior detection of the interference. The success of the proposed method is demonstrated into simulated and real automotive radar data sets, in the presence of Continuous Wave (CW) and Frequency Modulated Continuous Wave (FMCW) interference. Significant improvement in Signal-to-Interference-plus-Noise Ratio (SINR) is observed after range-Doppler processing.
5 November 2019 in IEEE Transactions on Vehicular Technology
Utilization of phase-coded waveforms in automotive MIMO radars for short to medium range applications is studied. Performances of three most-promising binary code families (Gold, APAS and ZCZ sequences) are compared. Design tradeoffs of practical implementation of phased-coded waveforms for MIMO radar are analyzed for the first time for a possible future System on Chip implementation. Orthogonality of the waveforms in case of moving targets is analyzed. The implications of the code properties for the Range-Doppler map, as well as the Range-Angular map, are pointed out. Doppler frequency shift impact on such performance indicators as the target peak power and range sidelobe levels in the range-Doppler plane, as well as the range and azimuth sidelobe behavior, and the angular error in the azimuthal plane have been comprehensively studied for the first time. It is shown that the time staggered transmit scheme with autocorrelation properties only (while introducing azimuthal errors) results in improved performance compared to code division multiplexing with auto- and cross-correlation properties.
This paper considers the interference mitigation problem for radar systems by focusing on emerging signal separation (decomposition) methods. We define appropriate transform domains to sparsely represent the interference and the signal of interest to separate them from each other. To show the effectiveness of the proposed algorithm at actual radar systems, the method is applied to real data from two different radar systems; The proposed method is applied to an automotive radar to mitigate the asynchronous interference caused by other automotive radars. Following, the proposed method is demonstrated on a polarimetric agile radar for synchronous mutual-interference mitigation. Significant improvements are observed at the signal-to-interference ratio (SIR) for both radar systems during the course of experiments.
11 January 2016 in IEEE Transactions on Geoscience and Remote Sensing
This paper addresses the mitigation of wind turbine clutter (WTC) in weather radar data in order to increase the performance of existing weather radar systems and to improve weather analyses and forecasts. We propose a novel approach for this problem based on signal separation algorithms. We model the weather signal as group sparse in the time-frequency domain; in parallel, we model the WTC signal as having a sparse time derivative. In order to separate WTC and the desired weather returns, we formulate the signal separation problem as an optimization problem. The objective function to be minimized combines total variation regularization and time-frequency group sparsity. We also propose a three-window short-time Fourier transform for the time-frequency representation of the weather signal. To show the effectiveness of the proposed algorithm on weather radar systems, the method is applied to simulated and real data from the next-generation weather radar network. Significant improvements are observed in reflectivity, spectral width, and angular velocity estimates.
A reconfigurable range-Doppler processing method for FMCW radar is presented. By concatenating beat-frequency signals from more than one sweep, a continuous beat-frequency signal for the whole coherent processing interval (CPI) can be created. As a result, continuous targets’ observation time is extended beyond that of a single chirp duration, leading to range resolution improvement. The created continuous beat-frequency signal can be split in the digital domain to any two-dimensional slow-time fast-time matrices with the same number of elements as in the original signals, which offers a realization of a software defined pulse/sweep repetition rate in Range-Doppler processing. The signal concatenation is done in the Short-time Fourier Transform (STFT) domain, where beat-frequency slices are extrapolated to compensate for the observation time lost in the transient region between sweeps, then a phase correction is applied to each frequency-slice as appropriate, followed by an Inverse STFT (ISTFT). The proposed technique is verified with simulation and experiments with an FMCW radar for stable and moving target scenarios. We found that the method allows for range resolution improvement without the transmission of additional bandwidth, and allows for the ability to observe different resolution granularities in parallel from one CPI. It additionally allows the decoupling of the transmitted PRF from the Doppler processing PRF, permitting the facility to observe different unambiguous Doppler velocity intervals from one CPI, without compromising on the total CPI processing gain.