Huan Liu

Dr. Huan Liu


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 November 2013 in Molecules
Verified
Journal Article
Open access
PDF file
HLHuan Liu
Huan Liu
CLChao Lin
Chao Lin
Zhen MaZhen Ma
Zhen Ma
HYHongbo Yu
Hongbo Yu
SZShenghu Zhou
Shenghu Zhou
Fe3O4 spheres with an average size of 273 nm were prepared in the presence of CTAB by a solvothermal method. The spheres were modified by a thin layer of SiO2, and then coated by mesoporous SiO2 (m-SiO2) films, by using TEOS as a precursor and CTAB as a soft template. The resulting m-SiO2/Fe3O4 spheres, with an average particle size of 320 nm, a high surface area (656 m2/g), and ordered nanopores (average pore size 2.5 nm), were loaded with gold nanoparticles (average size 3.3 nm). The presence of m-SiO2 coating could stabilize gold nanoparticles against sintering at 500 °C. The material showed better performance than a conventional Au/SiO2 catalyst in catalytic reduction of p-nitrophenol with NaBH4. It can be separated from the reaction mixture by a magnet and be recycled without obvious loss of catalytic activity. Relevant characterization by XRD, TEM, N2 adsorption-desorption, and magnetic measurements were conducted.

1 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
RFRuijie Feng
Ruijie Feng
HWHaibo Wu
Haibo Wu
HLHuan Liu
Huan Liu
YYYitian Yang
Yitian Yang
BPBingbing Pei
Bingbing Pei
ZHZhengren Huang
Zhengren Huang
The effects of Ti doping on the microstructure and properties of SiCp/Al composites fabricated by pressureless infiltration were comprehensively investigated using first-principles calculations and experimental analyses. First-principles calculations revealed that the interface wetting and bonding strength in an Al/SiC system could be significantly enhanced by Ti doping. Subsequently, the Ti element was incorporated into SiC preforms in the form of TiO2 and TiC to verify the influence of Ti doping on the pressureless infiltration performance of SiCp/Al composites. The experimental results demonstrated that the pressureless infiltration of molten Al into SiC preforms was promoted by adding TiC or TiO2 due to the improved wettability. However, incorporating TiO2 leads to the growth of AlN whiskers under a N2 atmosphere, thereby hindering the complete densification of the composites. On the other hand, TiC doping can improve wettability and interface strength without deleterious reactions. As a consequence, the TiC-doped SiCp/Al composites exhibited excellent properties, including a high relative density of 99.4%, a bending strength of 287 ± 18 MPa, and a thermal conductivity of 142 W·m−1·K−1.

5 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
XCXiuzheng Chen
Xiuzheng Chen
HWHaibo Wu
Haibo Wu
HLHuan Liu
Huan Liu
YYYitian Yang
Yitian Yang
BPBingbing Pei
Bingbing Pei
ZHZhengren Huang
Zhengren Huang
Zirconium carbide (ZrC) ceramics have a high melting point, low neutron absorption cross section, and excellent resistance to the impact of fission products and are considered to be one of the best candidate materials for fourth-generation nuclear energy systems. ZrC ceramics with a high relative density of 99.1% were successfully prepared via pressureless sintering using a small amount of MoSi2 as an additive. The influence of the MoSi2 content on the densification behavior, microstructure, mechanical properties, and thermal properties of ZrC ceramics was systematically investigated. The results show that the densification of ZrC was significantly enhanced by the introduction of MoSi2 due to the formation of a liquid phase during sintering. In addition, the ZrC grains were refined due to the pinning effect of the generated silicon carbide. The flexural strength and Vickers hardness of ZrC ceramics with 2.5 vol% MoSi2 sintered at 1850 °C were 408 ± 12 MPa and 17.1 GPa, respectively, which were approximately 30% and 10% higher compared to the samples without the addition of MoSi2. The improved mechanical properties were mainly attributed to the high relative density (99.1%) and refined microstructure.

25 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
RFRuijie Feng
Ruijie Feng
HWHaibo Wu
Haibo Wu
HLHuan Liu
Huan Liu
YYYitian Yang
Yitian Yang
BPBingbing Pei
Bingbing Pei
ZHZhengren Huang
Zhengren Huang
High-performance SiCp/Al composites were fabricated via a vacuum hot-pressing powder metallurgy process. The effects of SiC particle size on the composite microstructures and their thermal and mechanical properties were systematically investigated. The vacuum hot-pressed SiCp/Al composites exhibited a well-bonded interface between the SiC particles and Al matrix, while not exhibiting any Al4C3 brittle phase. Particle gradation effectively enhanced the densification of SiCp/Al composites, resulting in dense bulks with a relative density of 99.7%. When the SiC particle size increased from 5 to 50 μm, the fracture morphologies gradually transitioned from intergranular to transgranular, while the relative density, bending strength, and thermal conductivity increased. Overall, SiCp/Al composites with excellent thermal conductivity (201.42 W/(m·K)) and bending strength (523 ± 29.45 MPa) were obtained. To address the scarcity of research on SiCp/Al composites’ thermal properties, this study establishes SiC size/gradation–property relationships, innovatively filling the gap in thermal performance regulation.

21 May 2026 in Materials
Verified
Journal Article
Open access
PDF file
MJMa Junping
Ma Junping
HWHaibo Wu
Haibo Wu
HLHuan Liu
Huan Liu
YYYitian Yang
Yitian Yang
ZLZehua Liu
Zehua Liu
ZHZhengren Huang
Zhengren Huang
Zirconium carbide (ZrC) is a leading candidate for advanced nuclear reactor components due to its ultra-high melting point, thermomechanical stability, and low neutron absorption. However, its irradiation damage behavior and mechanism remains underexplored. In this work, dense pressureless-sintered ZrC ceramics with low-neutron-absorption MoSi2 additives were irradiated with 500 keV He2+ ions at room temperature to peak damage levels of 0.30, 1.49, and 2.97 dpa. The changes in their microstructure, bonding states, and property were analyzed via TEM, GIXRD, Raman spectroscopy, nanoindentation, and TDTR. ZrC retained crystallinity regardless of high-density black-spot defects, while MoSi2 exhibited severe amorphization and swelling. Lattice expansion and partial Zr-C bond breakage with C-C bond formation were confirmed, with maximum hardening at 1.49 dpa and significant elastic modulus reduction at 2.97 dpa. Thermal conductivity decreased modestly and showed minimal dose dependence, indicating a saturation effect. These results elucidate defect evolution in pressureless-sintered ZrC-MoSi2 ceramics and support its application in high-irradiation nuclear environments.