Farm tractor skidding is one of the common methods of timber extraction in Turkey. However, the absence of an optimal skidding plan covering the entire production area can result in time loss and negative environmental impacts. In this study, the timber extraction by farm tractors was analyzed, and a new skid trail pattern design was developed using Linear Programming (LP) and Geographical Information Systems (GIS). First, a sample skidding operation was evaluated with a time study, and an optimum skidding model was generated with LP. Then, the new skidding pattern was developed by an optimum skidding model and GIS analysis. At the end of the study, the developed new skid trail pattern was implemented in the study area and tested by running a time study. Using the newly developed “Direct Skid Trail Pattern (DSTP)” model, a 16.84% increase in working time performance was observed when the products were extracted by farm tractors compared to the existing practices. On the other hand, the average soil compaction value measured in the study area at depths of 0–5 cm and 5–10 cm was found to be greater in the sample area skid trails than in the control points. The average density of the skid trails was 281 m/ha, while it decreased to 187 m/ha by using the developed pattern. It was also found that 44,829 ton/ha of soil losses were prevented by using the DSTP model; therefore, environmental damages were decreased.
15 January 2024 in Environmental Monitoring and Assessment
The deterioration of the surface of forest roads is an important factor affecting the safe navigation of vehicles and traffic safety. In addition to traditional methods, automated methods are also used to determine the deterioration of the road surface. UAV systems, which are among the automated methods, are widely used to determine surface deformations with high accuracy. This study aimed to evaluate the advantages and disadvantages of two different flight modes of UAV, including autonomous flight and manual flight, in mapping road surface deformations. Within the scope of this study, the 50-meter section of the Type B forest road located in Kardüz Forest Management Chief (Düzce/Türkiye), was selected. For this study, first the pros and cons of the autonomous and manual flight data acquisition process were evaluated. Then, the photogrammetric data processing results were compared in terms of data size, with precision and accuracy. In addition, the deformation status on the surface within the selected road was determined using the average Z value differences obtained with two flight methods. The result of the study showed that, the number of images obtained from manual flights was 5.5 times higher than from autonomous flights and the flight time was taken four times longer. The average ground sampling distance of the orthophotos generated from two different light modes indicated that the manual flight mode provided seven times higher resolution than autonomous flight. Moreover, the results from the statistical tests for the two flight modes showed differences. When manual flights and autonomous flights are evaluated in terms of reducing the shadow effect, manual flights can be considered more advantageous. Furthermore, it was found that the dynamic mobility of erosion and accumulation on the road surface continued in time series in both flight methods.
This study compared the use of wood chips and slash to reduce the loss of sediment on newly constructed forest road slopes and investigated the annual amount of sediment loss on bare forest road slopes. A runoff block (sample field) was established for each of the four designated test sites (two cutslopes and two fillslopes). Each block had three runoff plots. One of the runoff plots was left empty for the control (CNT), while wood chips (C) and slash (S), respectively, were deposited in the other two. A total of 108 water samples were taken from the test sites and the amount of their suspended sediment calculated in the laboratory. As a result of this study, it was determined that the amount of soil loss in the control plots was about 1.26 times higher than in the slash plots and 2.21 times higher than in the wood chips plots. According to the results of variance analysis on the amounts of sediment, a statistically significant difference was found between the suspended sediment quantities transported on the road slopes (p < 0.05). However, no statistically significant difference between the suspended sediment quantities transported in the plots and the other variables of aspect, gradient or road slope was revealed by the t-test (p > 0.05).
Ormancılıkta üretim aktivitelerinin planlanmasında ve orman yollarının tasarlanmasında, konumsal verilere dayalı karar destek sistemleri bazı ülkelerde yaygın olarak kullanılmaktadır. Son yıllarda, ormanlık alanların yüksek çözünürlükte ve doğrulukta sayısal yükseklik modellerinin (SYM) üretilmesinde İnsansız Hava Araçları (İHA) kullanılmaktadır. İHA ile iş yükü azaltılmakta, zaman kazanımı ve daha hassas veriler elde edilmektedir. Orman yolu yaklaşık maliyet ve hakediş cetvellerinin hazırlanmasında iş yükü fazla olmaktadır. Ayrıca yol yapımı bittikten sonra yüklenici firmaya ödenecek ücret hakediş (olur) cetvellerinde bulunan kesin maliyete göre belirlenmektedir. Bu çalışmanın amacı İHA teknolojisi ile hakediş orman yolu kazı ile dolgu hacimleri belirlenmiş ve zemin klasları da incelenmiştir. Seben Orman İşletme Müdürlüğü sınırları içerisinde yer alan Taşlıyayla Orman İşletme Şefliği 001 kodlu orman yolunun 100 metrelik kısmı çalışamaya konu edilmiştir. Çalışmaya konu yolun yapımından önce ve sonra İHA (drone) ile uçuşlar otonom olarak gerçekleşmiştir. Çalışma sonucunda, hakediş 384,23 m3 kazı ile 188,30 m3 dolgu hacmi ve 893,84 m2 kazı alanı ile 447,85 m2 dolgu alanı bulunmuştur. Ayrıca alanda toprak ve küskülük zemin klasları tespit edilmiştir.
Decision support systems based on spatial data are widely used in some countries for planning production activitiesin forestry and designing forest roads. In recent years, Unmanned Aerial Vehicles (UAVs) have been playingan active role in the production of high resolution and accurate digital elevation models (DEMs) of forested areas.In the preparation of progress payments for forest road construction works, the workload is high, while the feethat has to be paid to the contractor company after the completion of the road construction is determined accordingto the final cost in the progress payment schedules. In this study, the applicability of UAV technology for determiningforest road cut volume and land classification was investigated. A 640-meter section of the forest roadcoded 001 of Taşlıyayla Forest Management Sub-Directorate (Bolu/Türkiye) was examined in the study. Flightswith an UAV (drone) were carried out in autonomous mode before and after the construction of the road examinedin the study. In addition, in order to determine the amount of cut, measurements of the geometric characteristicsof the road were made in the field after the road construction. As a result of the study, 2189 m³ cut volumewas found with the UAV data with an average error of 3 cm. According to the field measurement results, theamount of cut was determined as 2080 m³. A difference of +5% was found between the UAV data and the fieldmeasurement results. In addition, using the JavaScript coding language on the Google Earth Engine platform, soil(46%) and loose soil (54%) land classification was identified from the orthophoto images. The obtained resultsreveal the usability of UAVs in determining forest road volumes.