Fine excipient particles or ‘fines’ have been shown to improve the dispersion performance of carrier-based formulations for dry powder inhalation. Mechanistic formulation studies have focussed mainly on explaining this positive effect. Previous studies have shown that higher drug contents may cause a decrease in dispersion performance, and there is no reason why this should not be true for fines with a similar shape, size and cohesiveness as drug particles. Therefore, the effects on drug detachment of ‘fine lactose fines’ (FLF, X50 = 1.95 µm) with a similar size and shape as micronised budesonide were studied and compared to those of ‘coarse lactose fines’ (CLF, X50 = 3.94 µm). Furthermore, interactions with the inhalation flow rate, the drug content and the mixing order were taken into account. The observed effects of FLF are comparable to drug content effects in that the detached drug fraction was decreased at low drug content and low flow rates but increased at higher flow rates. At high drug content the effects of added FLF were negligible. In contrast, CLF resulted in higher detached drug fractions at all flow rates and drug contents. The results from this study suggest that the effects of fines may be explained by two new mechanisms in addition to those previously proposed. Firstly, fines below a certain size may increase the effectiveness of press-on forces or cause the formation of strongly coherent fine particle networks on the carrier surface containing the drug particles. Secondly, when coarse enough, fines may prevent the formation of, or disrupt such fine particle networks, possibly through a lowering of their tensile strength. It is recommended that future mechanistic studies are based on the recognition that added fines may have any effect on dispersion performance, which is determined by the formulation and dispersion conditions.
Adhesive mixtures for inhalation are the most widely used type of formulation in dry powder inhalation products. Although they have been the subject of active research, the relationships between properties of the starting materials, the mixing and dispersion processes, and the dispersion performance of this type of formulation are generally poorly understood. Interactions between relevant variables have been mentioned as an important cause. By reviewing the effects on mixture dispersion performance of the most widely studied formulation variables we try to find out whether or not the understanding of adhesive mixtures has improved in recent years. We furthermore propose an approach that may potentially accelerate the process of understanding. General conclusions concerning the effects of the variables considered cannot be drawn, because inconsistent findings are reported throughout the literature for all of them. These inconsistencies are indeed largely the result of interactions between variables of the formulation and dispersion processes. Mechanisms for most of the observed effects and interactions have been proposed, but they often remain unproven and, therefore, speculative. We have attempted to condense the knowledge from the literature into a theoretical framework that is intended to help explain the interplay between variables. According to this framework, only few mixture properties are key to understanding the effects of and interactions between formulation variables. Therefore, we suggest that the development or optimisation of techniques to accurately characterise these mixture properties could be an effective approach to further the fundamental understanding of adhesive mixtures for inhalation and enable their rational engineering.
Tuberculosis is the leading cause of death from a single infectious pathogen worldwide. Lately, the targeted delivery of antibiotics to the lungs via inhalation has received increasing interest. In a previous article, we reported on the development of a spray-dried dry powder isoniazid formulation containing an L-leucine coating. It dispersed well but had poor physical stability. In this study, we aimed to improve the stability by improving the leucine coating. To this end, we optimized the spray-drying conditions, the excipient content, and the excipient itself. Using L-leucine, the tested excipient contents (up to 5%) did not result in a stable powder. Contrary to L-leucine, the stability attained with trileucine was satisfactory. Even when exposed to 75% relative humidity, the formulation was stable for at least three months. The optimal formulation contained 3% trileucine w/w. This formulation resulted in a maximum fine particle dose of 58.00 ± 2.56 mg when a nominal dose of 80 mg was dispersed from the Cyclops® dry powder inhaler. The improved moisture protection and dispersibility obtained with trileucine are explained by its amorphous nature and a higher surface enrichment during drying. Dispersion efficiency of the device decreases at higher nominal doses.
Tuberculosis is a major health problem and remains one of the main causes of mortality. In recent years, there has been an increased interest in the pulmonary delivery of antibiotics to treat tuberculosis. Isoniazid is one of these antibiotics. In this study, we aimed to characterize isoniazid and formulate it into a dry powder for pulmonary administration with little or no excipient, and for use in the disposable Twincer® inhaler. Isoniazid was jet milled and spray dried with and without the excipient l-leucine. Physiochemical characterization showed that isoniazid has a low Tg of −3.99 ± 0.18 °C and starts to sublimate around 80 °C. Milling isoniazid with and without excipients did not result in a suitable formulation, as it resulted in a low and highly variable fine particle fraction. Spray drying pure isoniazid resulted in particles too large for pulmonary administration. The addition of 5% l-leucine resulted in a fraction <5 µm = 89.61% ± 1.77% from spray drying, which dispersed well from the Twincer®. However, storage stability was poor at higher relative humidity, which likely results from dissolution-crystallization. Therefore, follow up research is needed to further optimize this spray dried formulation.
The drug content in adhesive mixtures for inhalation is known to influence their dispersion performance, but the direction and magnitude of this influence depends on other variables. In the past decades several mechanisms have been postulated to explain this finding and a number of possible interacting variables have been identified. Still, the role of drug content in the formulation of adhesive mixtures for inhalation, which includes its significance as an interacting variable to other parameters, is poorly understood. Therefore, the results from a series of drug detachment experiments are presented in which the effect of drug content and its dependence on flow rate, the mixing time and the type of drug is studied. Furthermore, it is investigated whether the effect depends on the range within which the drug content is changed. Quantitative and qualitative multiple order interactions are observed between these variables, which may be explained by a shifting balance between three different mechanisms. The results therefore demonstrate that accounting for (multiple order) interactions between variables has to be part of quality by design activities and the rational design of future experiments.
1 January 2019 in Therapeutic Advances in Chronic Disease
Background: Inhaled levodopa may quickly resolve off periods in Parkinson’s disease. Our aim was to determine the pharmacokinetics and tolerability of a new levodopa dry-powder inhaler. Methods: A single-centre, single-ascending, single-dose–response study was performed. Over three visits, eight Parkinson’s disease patients (not in the ‘off state’) received by inhalation 30 mg or 60 mg levodopa, or their regular oral levodopa. Maximum levodopa plasma concentration ( Cmax), time to maximum plasma concentration (Tmax) and area under the concentration time curve 0–180 min were determined. Spirometry was performed three times at each visit. Results: After inhalation, levodopa Tmax occurred within 15 min in all participants, whereas after oral administration, Tmax ranged from 20 min to 90 min. The bioavailability of inhaled levodopa without carboxylase inhibitor was 53% relative to oral levodopa with carboxylase inhibitor. No change in lung-function parameters was observed and none of the patients experienced cough or dyspnoea. No correlation was observed between inhalation parameters and levodopa pharmacokinetic parameters. Conclusion: Inhaled levodopa is well tolerated, absorbed faster than oral levodopa, and can be robustly administered over a range of inhalation flow profiles. It therefore appears suitable for the treatment of off periods in Parkinson’s disease.