Chao Ma

Dr. Chao Ma


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 March 2018 in Journal of Thermal Science
Verified
Journal Article
Closed access
PDF file
CMChao Ma
Chao Ma
YJYongbin Ji
Yongbin Ji
BGBing Ge
Bing Ge
SZShusheng Zang
Shusheng Zang
HCHua Chen
Hua Chen

1 June 2015 in Experimental Thermal and Fluid Science
Verified
Journal Article
Closed access
CMChao Ma
Chao Ma
XCXiaoling Chen
Xiaoling Chen
JWJianfei Wang
Jianfei Wang
SZShusheng Zang
Shusheng Zang
YJYongbin Ji
Yongbin Ji

4 August 2020 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
CMChao Ma
Chao Ma
KLKangbo Lu
Kangbo Lu
WLWenjiao Li
Wenjiao Li

14 August 2020 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
PDF file
CMChao Ma
Chao Ma
LKLu Kangbo
Lu Kangbo
LWLi Wenjiao
Li Wenjiao
Radial turbines used in turbochargers and micro-turbines are subjected to high inlet temperature. This creates high thermal stress in the turbines, and possible creep of turbine inducer blades, and can reduce turbines’ reliability. With the ever-stringent engine emission regulations and the continuous drive for engine power density, turbine inlet temperature is significantly increased recently and the risk of thermo-mechanical failure of turbine rotor is heightened. To solve this problem, an innovative turbine cooling method is proposed by injecting a small amount of compressor or intercooler discharge air onto the upper backdisc region of turbine rotor to cool the disc and the inducer blades. A conjugate heat transfer simulation was carried out to investigate the effects of this cooling method with a turbocharger turbine. Flow conditions and geometric configurations were investigated for their influences on the cooling effectiveness of the method. The results show that using the compressor discharger air after intercooler with only 0.5–2.0% of turbine mass flow, the averaged cooling efficiency of the turbine backdisc is promoted by 23–43%; only four to six jets may be needed to cool the entire backdisc; and turbine efficiency is reduced by less than 1% point.

27 November 2017 in Experimental Heat Transfer
Verified
Journal Article
Closed access
CMChao Ma
Chao Ma
YJYongbin Ji
Yongbin Ji
SZShusheng Zang
Shusheng Zang
HCHua Chen
Hua Chen
An experimental study on heat transfer characteristics of steam and air flows in a V-shaped ribbed channels was conducted. The effects of Reynolds numbers and rib angles on heat transfer of steam and air were obtained. The area-averaged Nusselt numbers of steam flow at a Reynolds number of 12,000 were 13.9%, 20.6%, 27.1%, and 27.9% higher than those of air flow for rib angles of 90°, 75°, 60°, and 45°, respectively. The correlations for Nusselt number in terms of Reynolds number and rib angle for steam and air in V-shaped ribbed channels were developed.

9 April 2021 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
PDF file
CMChao Ma
Chao Ma
YSYilong Su
Yilong Su
GZGuangqian Zhu
Guangqian Zhu
JZJianjian Zhang
Jianjian Zhang
In view of the development status of high-reliability and low-cost cooling technology for radial turbine of micro-gas turbine or vehicle turbocharger, the impingement cooling technology of the radial turbine back disc was proposed, and the improvement of the cooling efficiency and thermal stress of the turbine back disc was numerically simulated. The results show that the impingement cooling technology can greatly improve the cooling efficiency of the turbine back disc and reduce the stress level. When the relative cooling flow is 1.0%–3.0%, the average cooling efficiency of the lower part of the turbine back disc is increased by 258%–486% compared with no cooling, which can reduce the thermal stress at the fillet of the back disc by 140–216 MPa. Both the average cooling efficiency and the fillet stress of the back disc increase slightly as the relative position of the jet hole moves outward. When the relative cooling flow is controlled within 2.0%, the effect of this cooling technology on the performance of the turbine can be ignored.