An XYZ compliant micropositioner has been widely mentioned in precision engineering, but the displacements in the X, Y, and Z directions are often not the same. In this study, a design and optimization for a new XYZ micropositioner are developed to obtain three same displacements in three axes. The proposed micropositioner is a planar mechanism whose advantage is a generation of three motions with only two actuators. In the design strategy, the proposed micropositioner is designed by a combination of a symmetrical four-lever displacement amplifier, a symmetrical parallel guiding mechanism, and a symmetrical parallel redirection mechanism. The Z-shaped hinges are used to gain motion in the Z-axis displacement. Four flexure right-circular hinges are combined with two rigid joints and two flexure leaf hinges to permit two large X-and-Y displacements. The symmetrical four-lever displacement amplifier is designed to increase the micropositioner’s travel. The displacement sensor is built by embedding the strain gauges on the hinges of the micropositioner, which is developed to measure the travel of the micropositioner. The behaviors and performances of the micropositioner are modeled by using the Taguchi-based response surface methodology. Additionally, the geometrical factors of the XYZ micropositioner are optimized by teaching–learning-based optimization. The optimized design parameters are defined with an A of 0.9 mm, a B of 0.8 mm, a C of 0.57 mm, and a D of 0.7 mm. The safety factor gains 1.85, while the displacement achieves 515.7278 µm. The developed micropositioner is a potential option for biomedical sample testing in a nanoindentation system.
In situ nanoindentation is extensively employed for online observing deformation and mechanical behaviors of bio-materials. However, the existing designs of the positioning stages have limited performances for testing soft or hard biomaterials. Consequently, this paper proposes a new structural design of a compliant one degree of freedom (01-DOF) stage with faster response. In addition to a new design, this article applies an analytical method to estimate the kinematic and dynamic behaviors of the stage. Firstly, the 01-DOF stage is designed with two modules, including a displacement amplifier with six levers and a symmetric parallelogram mechanism. Secondly, a kinetostatic diagram of the stage is built by pseudo-rigid-body method. Then, the dynamic equation of the proposed stage is formulated using the Lagrange method. In order to speed up the response of the indentation system, the structural optimization of the stage is conducted via the Firefly algorithm. The results showed that the theoretical first-order resonant frequency is found at about 226.8458 Hz. The theoretical consequences are nearby to the verified simulation. Besides, this achieved frequency of the presented stage is greater than that of previous stages. In an upcoming study, the prototype will be fabricated by additive manufacturing method or a computerized wire cutting method in order to verify the analytical results with experimental results.
In this paper, a cascade control structure is suggested to control servo systems that normally include a servo motor in coupling with two kinds of mechanism elements, a translational or rotational movement. These kinds of systems have high demands for performance in terms of fastest response and no overshoot/oscillation to a ramp function input. The fractional-order proportional integral (FOPI) and proportional derivative (FOPD) controllers are addressed to deal with those control problems due to their flexibility in tuning rules and robustness. The tuning rules are designed in the frequency domain based on the concept of the direct synthesis method and also ensure the robust stability of controlled systems by using the maximum sensitivity function. The M-Δ structure, using multiplicative output uncertainties for both control loops simultaneously, is addressed to justify the robustness of the controlled systems. Simulation studies are considered for two kinds of plants that prove the effectiveness of the proposed method, with good tracking of the ramp function input under the effects of the disturbances. In addition, the robustness of the controlled system is illustrated by a structured singular value (µ) plot in which its value is less than 1 over the frequency range.
A novel compact 2-DOF compliant positioner is developed for the purpose of achieving good characteristics such as high natural frequency, high displacement amplification ratio, good linear motion, and compact structure based on its symmetrical structure. To be specific, the developed stage is proposed according to an advanced six-lever displacement amplifier arranged at an inclination angle of the rigid bar utilizing right circular hinges and a parallel guiding mechanism with integrated flexure leaf hinges to attain the above-mentioned characteristics and reduce the decoupling mobility error. First, to quickly assess the initial quality response, an integration method of kinetostatic analysis, the Lagrange method, and finite element analysis was applied to evaluate and verify the quality characteristic of the stage. The experimental result showed that the error between the analytical method and the FEA method was 1.3%, which was relatively small and reliable for quickly assessing the primary quality response of the proposed positioner. Next, to boost the important output characteristics of the developed positioner, the integration approach of the response surface method and NSGA-II algorithm was utilized to find the optimal design variables. Finally, a prototype was manufactured based on the CNC milling method to validate the experimental and FEA analysis results. The attained results show that the optimal results of safety factor and output displacement were 2.4025 and 248.9 µm. Moreover, the FEA verification results were 2.4989 and 242.16 µm, with errors for safety factor and output displacement between the optimal result and the FEA result of 3.86% and 2.78%, respectively. In addition, the simulation and experimental results of the first natural frequency were 371.83 Hz and 329.59 Hz, respectively, and the error between the FEA result and experimental result for the first natural frequency was 11.36%. Furthermore, the achieved results show that the relationship between input displacement and output displacement of the experimental result and the FEA result of the developed structure achieved a good linear connection. These results suggest that the proposed positioner will be a potential structure employed in precise positioning systems and nanoindentation testing positioning systems for checking bio-specimens’ behaviors.
11 May 2021 in Mathematical Problems in Engineering
Optimization of CNC Milling Parameters for Complex 3D Surfaces of SIMOLD 2083 Alloy Mold Core Utilizing Multiobjective Water Cycle Algorithm: In this article, an effective multiobjective optimization approach is exploited to search for the best milling parameters for CNC for complex 3d surfaces of SIMOLD 2083 alloy mold core. To improve the quality responses, the cutting factors are optimized by a combination of Taguchi method (TM), response surface method (RSM), and multiobjective water cycle algorithm (MWCA). Firstly, the design for initial series experiments of the cutting factors was generated via the TM. Thereafter, the regression models between the cutting factors and the surface roughness of the machined workpiece surface as well as milling time are formed via applying the RSM. Moreover, analysis of variance and sensitivity analysis are also executed to define the influences and crucial contributions of cutting parameters on the surface roughness and milling time. The results of analysis of variance showed that the factors which have main effects on surface roughness were spindle speed (42.42), feed rate (29.40), and cutting depth (6.59), respectively. Meanwhile, the feed rate with the influence of 92.6 was the most significant factor in controlling the milling time. Ultimately, based on mathematical models, the MWCA is performed to define the optimal factors. The optimal results indicated that the optimized surface roughness was about 0.260μm and the milling time was roughly 1012.767 (s). In addition, the errors between forecasted results and experimental verifications for the surface roughness and milling time are 2.04 and 5.39, respectively. Therefore, the results of experimental verifications are suitable with the forecasted results from the proposed optimization method. These results depicted that the proposed integration approach can define effectively the optimal cutting factors for CNC milling and expand to apply for complex multiobjective optimization problems.
22 April 2021 in Mathematical Problems in Engineering
A novel compliant z-stage is applied for positioning and indenting a specimen in nano/microindentation testing system. For an excellent operation, the proposed z-stage can concurrently satisfy multicriteria comprising high safety factor, small parasitic motion, and large output displacement. The key aims of this article are to present a novel design of the compliant z-stage as well as an effective integration methodology of Taguchi method, response surface method, weight factor calculation based on signal to noise, and the whale optimization algorithm to resolve a design optimal problem so as to enrich the quality performances of the proposed stage. Primarily, the z-stage is designed based on four-lever amplifier, compliant hinge shifted arrangement mechanism, zigzag-based flexure spring guiding mechanism, and symmetric six leaf hinges-based parallel guiding mechanism. Secondly, the number experiment data are achieved by the Taguchi method and finite element analysis. Subsequently, the regression functions among input variables and quality characteristics are formed by exploiting response surface method. In addition, the weight factors for every characteristic are defined. Additionally, the sensitivity analysis is accomplished for determining influences of input variables on quality responses. Ultimately, based on regression equations, the whale optimization algorithm is executed to define the optimal factors. The consequences indicated that the output deformation is about 454.55μm and the safety factor is around 2.38. Furthermore, the errors among the optimal consequences and the confirmations for the safety factor and output deformation are 7.12 and 4.25, correspondingly. By using Wilcoxon and Friedman methods, the results revealed that the proposed algorithm is better than the cuckoo search algorithm. Based on the quality convergence characteristics of hybrid approach, the proposed method is proficient for resolving complicated multiobjective optimization.