The structural, wettability, and optical characteristics of aluminum-doped zinc oxide (AZO) thin films were studied with the objective of understanding the impact of deposition power and deposition temperature. Thin films were deposited using a radio frequency (RF) magnetron sputtering technique. The power output of the RF was augmented from 200 to 260 W, and the temperature was increased from 50 to 200 °C, which led to the development of a (002) peak for zinc oxide. The study of film thickness was carried out using the Swanepoel envelope method from data obtained through the UV-Vis spectrum. An increase in surface roughness value was shown to be connected with fluctuations in temperature as well as increases in deposition power. The findings revealed that as deposition power and temperature increased, the value of optical transmittance decreased, ranging from 70% to 90% based on the deposition parameters within the range of wavelengths that extend from 300 to 800 nm. The wettability properties of the samples were studied, and the maximum contact angle achieved was 110°. A Peltier apparatus was utilised in order to investigate the anti-icing capabilities, which revealed that the icing process was slowed down 3.38-fold. This work extends the understanding of the hydrophobicity and anti-icing capabilities of AZO thin films, specifically increasing both attributes which provide feasible options for purposes requiring resistance to ice.
In the presented research, aluminum-doped zinc oxide (AZO) thin films were synthesized on high-power transmission lines using the RF magnetron sputtering process. The impact of deposition power (160 W to 280 W) and deposition pressure (2 Pa to 5 Pa), on key characteristics like material composition, wettability, anti-icing behavior, and average crystal size were analyzed. The optimization of wettability and anti-icing performance was carried out using two-factor, four-level design of the Taguchi method to study the combined effects of multiple parameters rather than the effect of a single parameter. Considerable variation in the water contact angle, from 92.3° to 123.6°, has been observed, suggesting an enhancement in hydrophobic nature with optimized condition. Anti-icing tests demonstrated that the coated surface delayed ice accumulation by approximately 4.56 times compared to the uncoated surface. X-ray diffraction (XRD) analysis was carried out to confirm notable changes in the intensity of the (002) peak along the c-axis, directly correlating with grain size modification. The change in surface roughness was studied using AFM and the results were compared to establish a relationship between surface roughness and average grain size. Overall, the findings highlight the critical role of deposition parameters and their interactions in modifying the surface and structural properties of AZO thin films, which demonstrates their potential application for improving the anti-icing performance of transmission lines.
Application of Titanium Aluminium Nitride (TiAlN) coatings on brass surfaces was accomplished using magnetron sputtering. Within the scope of this study, we evaluate the ways in which alterations to the sputtering power and working pressure influence the tribological and structural attributes of TiAlN films. For the purpose of analysing the surface morphology of the TiAlN coating, the scanning electron microscope (SEM) method was utilised. There was a progressive rise in the strength of the TiAlN coating's (103) and (107) peaks in each of the variations. An analysis was conducted to evaluate the tribological properties of the TiAlN coating using a pin-on-disc tribometer. The study involved varying the speeds, loads, and sliding lengths. The wear rates of brass pins coated with TiAlN ranged between 1.03×10-3 and 5.87×10-4 mm3/Nm, depending on the load, sliding distance, and speed. Conversely, TiAlN-coated brass pins prepared at varying power showed wear rates ranging from 1.83×10-4 to 5.87×10-4 mm3/Nm.
In the presented research, aluminum-doped zinc oxide (AZO) thin films were synthe-sized on high-power transmission lines using the RF magnetron sputtering process. The impact of deposition power (160 W to 280 W) and deposition pressure (2 Pa to 5 Pa), on the structural, surface, wettability and anti-icing properties of the films was thoroughly investigated. Key characteristics like material composition, wettability, an-ti-icing behavior, and average crystal size were analyzed. The optimization of wetta-bility and anti-icing performance was carried out using two-factor, four level design of the Taguchi method. Considerable variation in water contact angle from 92.3° to 123.6°, has been observed suggesting an enhancement in hydrophobic nature with op-timized condition. Anti-icing tests demonstrated that the coated surface delayed ice accumulation by approximately 4.56 times compared to the uncoated surface. X-ray diffraction (XRD) analysis was carried out to confirm notable changes in the intensity of the (002) peak along the c-axis, directly correlating with grain size modification. The change in surface roughness was studied using AFM and results were compared to es-tablish relation between surface roughness and average grain size. Overall, the find-ings highlight the critical role of deposition parameters and their interactions in modi-fying the surface and structural properties of AZO thin films, which demonstrates their potential application for improving the anti-icing performance of transmission lines.
The choice of brass as the substrate due to its widespread use in soft non-ferrous industrial components such as bearings and electrical connectors creates the primary basis of novelty in this study. While prior tribological studies on titanium aluminum nitride (TiAlN) coatings is primarily focused on hard substrates such as steel and WC–Co, this work addresses the research gap by presenting a systematic investigation of the combined influence of sputtering power and working pressure on TiAlN coatings deposited on brass. Application of TiAlN coatings on brass surfaces was accomplished using magnetron sputtering. Within the scope of this study, the influence of sputtering power and working pressure on the tribological and structural attributes of TiAlN films is evaluated. The analysis of surface morphology is carried out using scanning electron microscopy (SEM), while structural characteristics revealed a progressive increment in the intensity of the (103) and (107) peaks with variation in deposition parameters. An analysis was conducted to evaluate the tribological properties of the TiAlN coating using a pin-on-disk tribometer. The study involved varying the speeds, loads, and sliding lengths. The optimized condition achieved wear reduction as high as 22% compared to uncoated brass at a sliding distance of 785 m, which highlights the strong dependence of wear performance on deposition parameters. The wear rates of TiAlN-coated brass ranged between 1.03 × 10−3 and 5.87 × 10−4 mm3/Nm depending on parameters like load, sliding distance and speed. Conversely, TiAlN-coated brass pins prepared at varying power showed wear rates ranging from 1.83 × 10−4 to 5.87 × 10−4 mm3/Nm. These findings demonstrate that optimization of TiAlN coating parameters on brass can significantly enhance wear resistance, which ultimately improves the durability and performance of engineering components in tribological applications.