An ultrasonic plasticizing and pressing method (UPP) that fully utilizes ultrasonic vibration is proposed for fabricating thermoplastic polymer surface microstructures with high aspect ratios (ARs). The characteristics of UPP are elucidated based on the plasticization of the raw material, the melt flow, and the stress on the template microstructure during the forming process. Initially, the micronscale single-stage micropillar arrays (the highest AR of 4.1) were fabricated by using 304 stainless steel thin sheets with micronscale pore (through-hole) arrays as primary templates. Subsequently, anodic aluminum oxides (AAOs) with ordered nanoscale pore arrays were added as secondary templates, and the micro/nanoscale hierarchical micropillar arrays (the highest AR up to 24.1) were successfully fabricated, which verifies the feasibility and forming capability of UPP. The superiority and achievements of UPP are illustrated by comparing the prepared hierarchical micropillar arrays with those prepared in the previous work in four indexes: microstructure scale, aspect ratio, forming time, and preheating temperature of the raw material. Finally, the water contact angle (WCA) and oil droplet complete immersion time of the surface microstructures were measured by a droplet shape analyzer, and the results indicate that the prepared micropillar arrays are superhydrophobic and superoleophilic.

Unlike previous design procedures for parallel machine tools (PMTs), this paper first analyzes the path and posture requirements of the tools in universal processing, then proposes and constructs a new class of PMs that can provide the required path and posture. This opens up new ideas for the design of PMTs. Based on the reciprocal screw theory, a type synthesis process of asymmetrical lower-mobility PMs was proposed. Through this process, a novel class of four-limbed parallel mechanisms (PMs) providing three translations and one rotation around a horizontal axis (y-axis), denoted as 4-3T1R(y) PMs, was successfully proposed and constructed. Such PMs can be applied to the design of PMTs, especially the design of micro-electrical discharge machining (micro-EDM) PMTs. The structural design of a new 2RRC-2CRU PM, which was a member of 4-3T1R(y) PMs, was performed, and its mobility was analyzed in detail to demonstrate the efficiency of the proposed type synthesis process. The inverse, forward, and velocity kinematics problems of the 2RRC-2CRU PM were solved for further applications.

The development of absorber materials with strong light absorption properties and low-cost fabrication processes is highly significant for the application of photothermal conversion technology. In this work, a mixed powder consisting of NaCl, polypropylene (PP), and scale-like carbon flakes was ultrasonically pressed into sheets, and the NaCl was then removed by salt dissolution to obtain porous carbon polypropylene composite sheets (P-CPCS). This process is simple, green, and suitable for the low-cost, large-area fabrication of P-CPCS. P-CPCS has a well-distributed porous structure containing internal and external connected water paths. Under the dual effects of the carbon flakes and porous structure, P-CPCS shows excellent photothermal conversion performance in a broad wavelength range. P-CPCS-40 achieves a high temperature of 128 °C and a rapid heating rate of 12.4 °C/s under laser irradiation (808 nm wavelength, 1.2 W/cm² power). When utilized for solar steam generation under 1 sun irradiation, P-CPCS-40 achieves 98.2% evaporation efficiency and a 1.81 kg m⁻² h⁻¹ evaporation rate. This performance means that P-CPCS-40 outperforms most other previously reported absorbers in terms of evaporation efficiency. The combination of carbon flakes, which provide a photothermal effect, and a porous polymer structure, which provides light-capturing properties, opens up a new strategy for desalination, sewage treatment, and other related fields.

The influence of axial ultrasonic vibration (the dominant vibration mode) on the filling behavior of polymer melt in microcavities and its effect on microstructure formation remains inadequately understood. Based on the plasticization location and the extent to which the microcavity is covered by the ultrasonic sonotrode action surface, existing ultrasonic plasticization molding technologies were classified into three types—ultrasonic pressing (UP), ultrasonic plasticizing and pressing (UPP), and ultrasonic plasticization injection molding (UPIM). The effects of these configurations on melt fluidity and filling performance were evaluated and compared through slit flow tests. The interaction mechanisms between polymer melts and templates were elucidated based on melt pressure measurements and morphological changes in nickel micropillar arrays and silicon templates after molding. The results indicated that polymer melt exhibits improved flow behavior within microcavities when under the coverage area of the ultrasonic sonotrode action surface and subjected to the axial ultrasonic vibration. Continuous ultrasonic vibration contributed to sustaining melt fluidity during micropore filling. Among the three technologies, the most complex and intense mechanical interactions on the template microstructure were observed in UP, followed by UPP and then UPIM.