Mineral carbonation is one of the typical carbon capture, utilization, and storage technologies, to obtain synthetic carbonates from metal oxide and CO2. However, the technology is known to be extremely challenging to achieve economic feasibility because expensive chemical solvents used the account for most of the cost. To overcome this limitation, we conducted a pilot laboratory study to secure the economic viability of the technology by replacing these chemical solvents with costless metallic carbon dioxide cylinders. For the current study, we implement cement kiln dust (CKD), which is an alkali industrial by-product, together with mineral CO2 gas. In this research paper, we attained CO2 storage and CaCO3 yield, which is comparable in both quantitative and qualitative respects to the existing studies. With a steady flow rate of 0.9 L/m of carbon dioxide furthermore fixed time, the carbonation of CKD could increase dramatically, reaching 35% calcium carbonate at 550°C and 27% calcium carbonate at 450°C respectively. It was also found that CO2 flow rate is one component, which can elute Ca from CKD, and had significant effects on carbonation efficiency. The solid to liquid ratio was the most influential factor in the Ca elution process. the microstructure, morphology, and thermal traits of the designed patches are characterized using scanning electron microscopy (SEM) to indicate phases composition, X-Ray Diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) measurements.
21 January 2019 in Environmental Progress & Sustainable Energy
Biodiesel production process relies of various key steps one of which is the lipid extraction from microalgae cells using economic techniques. In this study, Algal community structure and physicochemical parameters of the wastewater treatment plant (Beni-Suef, Egypt), are determined from March 2016 to February 2017. In this study, we focused on the lipid extracted from wild mixed culture of Chlorella sp. which is the dominant from December 2016 to February 2017. Lipid content and fatty acid profiling of Chlorella sp. are investigated using three different methods (1) conventional extraction (CE), (2) ultrasonic assisted extraction (UAE) and (3) microwave assisted solvothermal extraction (MASE). MASE showed the highest lipid yield of 37.9±0.13%. SEM micrographs showed that MASE had the most distributive effect for algae cells compared to UAE and CE. Six different solvents are tested for MASE technique namely hexane: isopropanol (3:2), hexane: ethanol (1:1), chloroform: methanol (1:1), diethyl ether, ethanol and methanol. A strong linear relation between the direct electric constant and yield percent is obtained with methanol showing the highest yield. The GC-analysis of extracted lipids shows that methanol resulted in the highest percentage of palmitic acid (45.5%). The chemical composition of extracted lipids shows promise towards further conversion to biodiesel.
This work aims at the preparation and characterization of dual-layer (DL) nano-fibrous mat (NFM) of hydrophobic and mechanical stable polyacrylonitrile (PAN) nano-fibers (NFs), as a supporter, and polyamide 6 (PA)/chitosan (Ch) NFs as a top hydrophilic coating layer. PAN and PA fibers, as residual wastes from textile processes, were collected and dissolved in their proper solvents. PAN was electro-spuned under certain conditions of electro-spinning (voltage, flow rate, and distance between spinneret and collector) to obtain PAN-NFM. Different ratios of PA/Ch composite were prepared and then electro-spun above the PAN-NFM that was previously prepared to obtain hydrophobic/hydrophilic functional dual-layer nano-fibrous membrane (DLNFM). The efficiency of the prepared DLNFM for capturing dye residues and heavy metals from wastewater was investigated. The viscosities of the prepared composite solutions were measured. The prepared dual-layer nano-fiber membranes (DLNFMs) were chemically and physically characterized by Fourier transform infrared spectroscopy, scanning electron microscope, X-ray diffraction, and thermogravimetric analyzer. The potential of the prepared mats for the adsorption of some heavy metal ions, i.e., Cu+2, Cr+3, and Pb+2 cations in addition to dyes from wastewater was evaluated. The effect of using different concentrations of PA/Ch composite as well as the thickness of the obtained DLNFM on the filtration efficiency was studied. The results of this study show the success of functional DLNFM in dye and heavy metal removal. The maximum removal efficiency of acid dyes was reached to 73.4 % and of reactive dye was approximately 61 % for PAN/PA-1.25%Ch DLNFM after 3 days at room temperature. The removal efficiency percent of heavy metal ions reached to 54 % by DLNFM. Additionally, the results showed that 0.08 mm is the ideal thickness for maximum absorption capacity. This value is correlated with the membrane's highest Ch percentage, which is (PAN/PA-1.25%Ch). Furthermore, the results demonstrate that the presence of the Ch polymer strengthened the produced bi-layered membrane to achieve the highest thermal stability when compared to the other nano-fibrous membranes (NFMs), with the breakdown temperature of the Ch functionalized dual-layer membranes (DLMs) reaching approximately 617 °C and a maximum weight loss of 60 %.
Renewable energy and alternative fuel from different conventional resources such as biomass, plastic waste, and recyclable polymers are impertinent environmental issues worldwide. Furthermore, to replace fossil fuel and reduce greenhouse gas emissions that have a negative impact on climate change. This article exhibits the effect of metal oxide composite/clay in the thermal decomposition of Polypropylene. That hetrocatalyst composed nano-clay thin layer loaded with MnO2-NPs works on cracking of polypropylene under different reaction conditions like heating temperature, rate of reaction, reaction time, and composite loading ratio. Various techniques such as GC and TEM were used to characterize pyrolysis gases and char, in addition to scanning electron microscopy (SEM), Fourier transform infrared (FTIR), Thermo-gravimetric analyzer (TGA), and X-ray diffraction (XRD) were used for composite characterize. High gas yield and char rate conversion were obtained using synthesize composite.