This paper describes a new three-dimensional (3D) fused filament additive manufacturing (AM) technique in which electroactive polymer filament material is used to build soft active 3D structures, layer by layer. Specifically, the unique actuation and sensing properties of ionic polymer-metal composites (IPMCs) are exploited in 3D printing to create electroactive polymer structures for application in soft robotics and bio-inspired systems. The process begins with extruding a precursor material (non-acid Nafion precursor resin) into a thermoplastic filament for 3D printing. The filament is then used by a custom-designed 3D printer to manufacture the desired soft polymer structures, layer by layer. Since at this stage the 3D-printed samples are not yet electroactive, a chemical functionalization process follows, consisting in hydrolyzing the precursor samples in an aqueous solution of potassium hydroxide and dimethyl sulfoxide. Upon functionalization, metal electrodes are applied on the samples through an electroless plating process, which enables the 3D-printed IPMC structures to be controlled by voltage signals for actuation (or to act as sensors). This innovative AM process is described in detail and the performance of 3D printed IPMC actuators is compared to an IPMC actuator fabricated from commercially available Nafion sheet material. The experimental results show comparable performance between the two types of actuators, demonstrating the potential and feasibility of creating functional 3D-printed IPMCs.
31 August 2020 in IEEE Transactions on Automation Science and Engineering
This article describes a Voronoi-based path generation (VPG) algorithm for an energy-constrained mobile robot, such as an unmanned aerial vehicle (UAV). The algorithm solves a variation of the coverage path-planning problem where complete coverage of an area is not possible due to path-length limits caused by energy constraints on the robot. The algorithm works by modeling the path as a connected network of mass-spring-damper systems. The approach further leverages the properties of Voronoi diagrams to generate a potential field to move path waypoints to near-optimal configurations while maintaining path-length constraints. Simulation and physical experiments on an aerial vehicle are described. Simulated runtimes show linear-time complexity with respect to the number of path waypoints. Tests in variously shaped areas demonstrate that the method can generate paths in both convex and nonconvex areas. Comparison tests with other path generation methods demonstrate that the VPG algorithm strikes a good balance between runtime and optimality, with significantly better runtime than direct optimization, lower cost coverage paths than a lawnmower-style coverage path, and moderately better performance in both metrics than the most conceptually similar method. Physical experiments demonstrate the applicability of the VPG method to a physical UAV, and comparisons between real-world results and simulations show that the costs of the generated paths are within a few percent of each other, implying that analysis performed in simulation will hold for real-world application, assuming that the robot is capable of closely following the path and a good energy model is available.
This paper presents a new manufacturing and control paradigm for developing soft ionic polymer-metal composite (IPMC) actuators for soft robotics applications. First, an additive manufacturing method that exploits the fused-filament (3D printing) process is described to overcome challenges with existing methods of creating custom-shaped IPMC actuators. By working with ionomeric precursor material, the 3D-printing process enables the creation of 3D monolithic IPMC devices where ultimately integrated sensors and actuators can be achieved. Second, Bayesian optimization is used as a learning-based control approach to help mitigate complex time-varying dynamic effects in 3D-printed actuators. This approach overcomes the challenges with existing methods where complex models or continuous sensor feedback are needed. The manufacturing and control paradigm is applied to create and control the behavior of example actuators, and subsequently the actuator components are combined to create an example modular reconfigurable IPMC soft crawling robot to demonstrate feasibility. Two hypotheses related to the effectiveness of the machine-learning process are tested. Results show enhancement of actuator performance through machine learning, and the proof-of-concepts can be leveraged for continued advancement of more complex IPMC devices. Emerging challenges are also highlighted.
A new nonparametric Bayesian-based motion planning algorithm for autonomous plume source term estimation (STE) and source seeking (SS) is presented in this paper. The algorithm is designed for mobile robots equipped with gas concentration sensors. Specifically, robots coordinate and utilize a Gaussian-plume likelihood model in a Bayesian-based STE process, then they simultaneously search for and navigate toward the source through model based, bioinspired SS methods such as biased-random-walk and surge-casting. Compared with the state-of-the-art Bayesian- and sensor-based STE/SS motion planners, the strategy described takes advantage of coordination between multiple robots and the estimated plume model for faster and more robust SS, rather than rely on direct or filtered sensor measurements. A set of Monte Carlo simulation studies are conducted to compare the performance between the uncoordinated and coordinated algorithms for different robot team sizes and starting conditions. Additionally, the algorithms are validated experimentally through a laboratory-safe, realistic humid-air plume that behaves similar to a gas plume, to test STE and SS using mobile ground robots equipped with humidity sensors. Simulation and experimental results show consistently that the algorithm involving coordination outperforms traditional bioinspired SS algorithms and it is approximately twice as fast as the uncoordinated case. Finally, the plume source is distorted to study the algorithm's limitations and impact on STE and SS, where results show that even for distorted plumes, useful source localization information can be obtained.
2 October 2017 in International Journal of Smart and Nano Materials
Smart polymeric and gel actuators change shape or size in response to stimuli like electricity, heat, or light. These smart polymeric- and gel-based actuators are compliant and well suited for development of soft mechatronic and robotic devices. This paper provides a thorough review of select smart polymeric and gel actuator materials where an automated and freeform fabrication process, like 3D printing, is exploited to create custom shaped monolithic devices. In particular, the advantages and limitations, examples of applications, manufacturing and fabrication techniques, and methods for actuator control are discussed. Finally, a rigorous comparison and analysis of some of the advantages and limitations, as well as manufacturing processes, for these materials, are presented.