The propagation properties of leaky surface acoustic waves (LSAWs) and longitudinal-type LSAWs (LLSAWs) on a LiNbO 3 (LN) or LiTaO 3 (LT) thin plate bonded to an AT-cut quartz or c -plane sapphire ( c -Al 2 O 3 ) substrate with a high phase velocity were investigated. It was theoretically revealed that when the LN or LT thin-plate thickness is less than one wavelength, the particle displacement of LLSAWs was concentrated in the thin plate and the electromechanical coupling factor ( K2 ) was increased to two to three times that in the single substrate. Furthermore, for 36° Y -cut X -propagating LT/ c -Al 2 O 3 with an LT thin-plate thickness of 0.35 λ and X -cut 36° Y -propagating LN/ c -Al 2 O 3 with an LN thin-plate thickness of 0.19 λ, the values of K2 for an LSAW and an LLSAW were experimentally found to increase from 5.6 and 10.4% in the single substrate to 11.5 and 19.7% in the thin-plate bonded structure, respectively.
19 June 2018 in Japanese Journal of Applied Physics
The propagation properties and resonance characteristics of leaky surface acoustic waves (LSAWs) and longitudinal-type LSAWs (LLSAWs) on a LiTaO 3 (LT) thin plate bonded to an AT-cut quartz substrate were investigated experimentally. For the LSAWs and LLSAWs, the bonded structures of 36° Y -cut X -propagating LT (36°YX-LT)/AT-cut 90° X -propagating quartz (AT90°X-quartz) and X -cut 31° Y -propagating LT (X31°Y-LT)/AT-cut 45° X -propagating quartz (AT45°X-quartz) were fabricated, respectively. For the LSAW on 36°YX-LT/AT90°X-quartz, the electromechanical coupling factor ( K2 ) of 11.1% was obtained at an LT thin-plate thickness of 0.25 wavelength, whereas K2 for a single LT substrate was measured to be 5.7%. For the LLSAW on X31°Y-LT/AT45°X-quartz, K2 increased from 2.8% for the single LT substrate to 7.2% at an LT thin-plate thickness of 0.14 wavelength. Furthermore, K2 of approximately 12% and the temperature coefficient of frequency (TCF) of 0 ppm/°C were theoretically obtained simultaneously for the LSAW on 36°YX-LT/AT-cut 90°X-quartz at a certain thin-plate thickness.
26 April 2021 in Japanese Journal of Applied Physics
In this paper, first, the surface acoustic wave (SAW) propagation mode and a method of analyzing the propagation property are introduced briefly. Then, typical composite substrate structures that have been developed to obtain high-performance SAW devices are reviewed. Furthermore, the recent results obtained by the author and research colleagues on the propagation and resonance properties of leaky SAW (LSAW) and longitudinal-type LSAW on dissimilar-material bonded structures comprising a LiTaO 3 (LT) or LiNbO 3 thin plate with a thickness of less than 1 λ ( λ ː wavelength) and a quartz substrate are described. The control of attenuation and the cause of large coupling factor of LSAWs by utilizing layered structures were also discussed. For the bonded 4 inch wafer of 36°YX-LT/AT90°X-quartz with a thin-plate thickness of 0.3 λ , an admittance ratio of 81 dB, a fractional bandwidth of 4.2%, and resonance and antiresonance factors of approximately 1500 with markedly improved properties compared with a single 36°YX-LT substrate were obtained experimentally at 2.2 GHz.
1 July 2019 in Japanese Journal of Applied Physics
To obtain a bonded structure with low attenuation for longitudinal leaky surface acoustic waves (LLSAWs), the propagation and resonance properties on a LiTaO 3 (LT) or LiNbO 3 thin plate bonded to an X-cut quartz substrate were theoretically analyzed. The attenuation of an X-cut 31°Y-propagating LT (X31°Y-LT)/X32°Y-quartz (X32°Y-Q) was calculated to be 0.0005 dB/ λ at the normalized LT thin plate thickness h/λ = 0.062 ( λ : wavelength) and was lower than that on an X31°Y-LT/AT45°X-Q. Using a finite element method, for the X31°Y-LT/X32°Y-Q, the admittance ratio and Q factor were improved to 120 dB and 53 400 from 62 dB and 1000 for the X31°Y-LT/AT45°X-Q, respectively. Then, the propagation and resonance properties were measured. For the X31°Y-LT/X32°Y-Q, the measured electromechanical coupling factor ( K2 ) and Q factor increased to 5.6% and 280 from 1.8% and 32 for the single LT, respectively. The temperature coefficient of frequency of the LLSAW was measured to be −26.2 ppm °C −1 .
13 June 2016 in Japanese Journal of Applied Physics
The propagation properties of a leaky surface acoustic wave (LSAW) on rotated Y-cut X-propagating lithium niobate (YX-LN) substrates loaded with an aluminum nitride (AlN) thin film with a higher phase velocity than that of the substrate were investigated theoretically and experimentally. From the theoretical calculation, it was found that the minimum attenuation can be obtained at a certain thickness of the AlN thin film for a cut angle ranging from 0 to 60° because the cut angle giving the minimum attenuation shifts toward a smaller cut angle as the film thickness is increased. The propagation properties of an LSAW on several rotated YX-LN substrates were measured by using an interdigital transducer (IDT) pair with a wavelength λ of 8 µm, and the predicted shifts of the minimum attenuation toward a smaller cut angle were demonstrated experimentally. For 0° and 10°YX-LN samples, the measured insertion loss and propagation loss were markedly reduced by loading with the AlN thin film. A larger electromechanical coupling factor (16.9%) than that at the cut angle giving zero attenuation without a film and a propagation loss less of 0.02 dB/λ were obtained simultaneously at a film thickness of 0.125 λ for the 10°YX-LN sample.
15 April 2021 in Japanese Journal of Applied Physics
The enhancement of high-order surface acoustic wave (SAW) harmonics by increasing the metallization ratio was theoretically and experimentally investigated in high-performance bonded dissimilar-material structures. The simulation using a finite element method for 36°Y-cut X-propagating LiTaO 3 (36°YX-LT)/AT-cut 90°X-propagating quartz (AT90°X-quartz) and 27°YX-LiNbO 3 /AT90°X-quartz was performed by setting the metallization ratio of the interdigital transducer to a/p = 0.8 ( a : electrode width, p : pitch), and the LT and LN thin-plate thicknesses to h / λ = 0.05 ( λ : wavelength) and 0.1, respectively. The fractional bandwidths for 36°YX-LT/AT90°X-quartz and 27°YX-LN/AT90°X-quartz were obtained to be 1.6% and 4.0%, respectively, which were larger than those for single LT and LN. For a leaky SAW (LSAW) resonator with a / p = 0.8 fabricated on 36°YX-LT/AT0°X-quartz, the resonance properties and temperature coefficient of frequency of LSAW fundamental waves and harmonics were measured. The measured fractional bandwidth increased from 0.8% to 1.4% for single LT.