Electrospinning has been known for its’ ability in producing nanoporous fibres which uses electrical force to form a spinning jet out of a polymer solution. The electrospinning condition and polymer solution properties can influence the electrospinning jet formation as well as jet path. Polylactic acid (PLA) was dissolved in dimethylformamide (DMF) to produce a polymer solution. Bead is considered as a defect towards an electrospun fibres, yet previous study found that PLA/DMF produced beaded fibres for all concentrations. However, there is a limited study that explain the effect of concentration on the diameter of beads. Therefore, in this study we investigated the formation of electrospinning jet as well as the effect of PLA concentration of formation of beads, particularly the diameter of the beads. Polymer solution with different concentration was prepared. The concentration investigated in this study were 7.5, 10, 12.5, 15, 17.5, and 20 % w/v. Polymer solution was then subjected to the electrospinning process to evaluate the morphology of the electrospun produced via optical microscope. Simultaneously, the formation of electrospinning jet is observed with portable digital microscope. The morphology of the electrospun fibres, especially the fibre and bead diameter are analyzed using image analysis software, ImageJ. From this research, it is found that at voltage of 10 and 12.8 kV, a stable electrospinning jet can be formed which consists of ‘Taylor cone’, straight jet, and plume. Concentration from 7.5–20 % w/v were able to form electrospun fibres, yet only 12.5 and 15 % w/v PLA concentrations can produce an effective electrospun fibres with beads diameter of 3393 nm and 3642 nm, respectively. Also, the number of beads for both concentrations are 34 and 19, respectively. Since the main criteria in producing electrospun fibres is no beads or small and minimal beads at best, therefore 12.5 and 15 % w/v PLA concentration are considered as efficient electrospun fibres.
13 February 2020 in Asia-Pacific Journal of Chemical Engineering
Composite Nickel (Ni) coatings, which contain submicron graphite particles (400 nm in size), were deposited on AISI 1045 steel using a direct current electrodeposition technique from a Watts bath. The effects of different graphite particle concentrations (0, 0.2, 0.5 and 1 g/L) on the surface and tribological properties of the composite Ni coatings were investigated. The introduction of graphite particles into a Ni electrodeposit was found to result in grain refinement, and the broccoli-like cluster structure was formed on the coating surface. Hence, the hydrophobicity of the coating was greatly improved. When the concentration of graphite particles is 1 g/L, the hardness of the composite coating reaches 13.200 ± 0.128 GPa and the smallest width values of the wear scars as compared to the pristine Ni coating, which had a hardness of 2.628 ± 0.033 GPa. These results reveal that the fine-grain strengthening effect and formation of a graphite-rich protective layer on the contact surfaces effectively enhance the tribological performance of the coating.
1 April 2020 in IOP Conference Series: Earth and Environmental Science
Carbon dioxide, a type of greenhouse gases has drawn world wide’s attention as major contributors to global warming and climate change. Thus, several methods have been developed to mitigate this problem such as through adsorption. There are numerous types of adsorbents available, for instance is carbon-based adsorbent that can be synthesised from various type of biomass as reported in previous studies. However, there are very few studies used soil as an adsorbent for gases. Soils are porous medium developed in the uppermost layer of Earth’s crust which are available in several forms, abundance and cheap. In this study, three types of carbonised soils were used as carbon-based adsorbent to investigate its adsorption capacity for carbon dioxide. Influence of moisture content in this study is negligible as it is too low. Due to the nature of raw materials used, ash content for all sample was incredibly high which almost all exceeded 90%. Determination of densities by pycnometer showed that carbonised soil 2 has the lowest particle and bulk density of 2.4802 g/cm3 and 0.5248 g/cm3 respectively. Then the adsorption capacity of each sample was determined by sorption measuring instrument with magnetic suspension balance. Results showed that carbonised soil 2 with high surface area, pore volume, and small pore size has the highest adsorption capacity of 6.4 mg/g at 25 ˚C under atmospheric pressure. Therefore, soils exhibit prominent potential to be developed as carbon dioxide adsorbent with desirable properties.
Electrospray is a novel and versatile approach to the synthesis of nanosized particles. In this paper, the effects of electrospray process parameters such as gauge size (18 G-25 G) and flow rate (0.9-1.5 ml hr-1) on droplet surface tension and electrospray particle size were evaluated. 25 mg Poly Lactic-co-Glycolic Acid (PLGA) were dissolved in 100 ml acetone before being subjected to electrospray. Tate’s Law was used to calculate the surface tension while the Malvern nanosizer was used to measure the particle size. Based on Tate’s Law calculation, when the gauze size increased from 18 G-25 G, the droplet surface tension increased from 10.07 Nm-1 to 18.17 Nm-1 showing a direct pattern. At the same time, the flowrate is inversely proportional to droplet surface tension. When the flow rate increased from 0.9-1.5 ml hr-1, the droplet surface tension was reduced. This is due to the increasing ratio of vicious force and surface tension. For particle size, as surface tension increased from 10.07 Nm-1 to 18.17 Nm-1, particle size increased from 205.57 nm to 612 nm owing to the corona discharge producing larger progeny droplets that chain into smaller particles through coulomb fission as more charge is required to overcome the surface tension. In conclusion, flow rate and gauge size influenced the surface tension thus affecting the nanosized particles.