Sina Shahbazmohamadi

Dr. Sina Shahbazmohamadi

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 October 2017 in ACS Nano
Verified
Journal Article
Closed access
AVArmin VahidMohammadi
Armin VahidMohammadi
AHAli Hadjikhani
Ali Hadjikhani
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
MBMajid Beidaghi
Majid Beidaghi

13 April 2016 in ACM Journal on Emerging Technologies in Computing Systems
Verified
Journal Article
Open access
PDF file
MQMd Shahed Enamul Quadir
Md Shahed Enamul Quadir
JCJunlin Chen
Junlin Chen
DFDomenic Forte
Domenic Forte
NANavid Asadizanjani
Navid Asadizanjani
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
MTMark Tehranipoor
Mark Tehranipoor
The reverse engineering (RE) of electronic chips and systems can be used with honest and dishonest intentions. To inhibit RE for those with dishonest intentions (e.g., piracy and counterfeiting), it is important that the community is aware of the state-of-the-art capabilities available to attackers today. In this article, we will be presenting a survey of RE and anti-RE techniques on the chip, board, and system levels. We also highlight the current challenges and limitations of anti-RE and the research needed to overcome them. This survey should be of interest to both governmental and industrial bodies whose critical systems and intellectual property (IP) require protection from foreign enemies and counterfeiters who possess advanced RE capabilities.

1 May 2018 in Optics and Lasers in Engineering
Verified
Journal Article
Closed access
KAKiarash Ahi
Kiarash Ahi
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
NANavid Asadizanjani
Navid Asadizanjani

8 July 2019 in Microscopy Today
Verified
Journal Article
Open access
PDF file
RHRod Heu
Rod Heu
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
JYJohn Yorston
John Yorston
PCPatrick Capeder
Patrick Capeder
This article describes target material options for sputter coaters that deposit a thin metal coating on non-conductive SEM samples. Coating a sample with a conductive metal renders an insulating sample conductive enough to minimize charging effects on the SEM image. In most cases, coating SEM samples with only a few nanometers of a metal results in crisp, clear images. Proper target material selection is dictated by overall imaging requirements, the SEM available, the specimen material being evaluated, and whether X-ray microanalysis will be required.

1 November 2015
Verified
Conference Paper
Closed access
PDF file
NANavid Asadizanjani
Navid Asadizanjani
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
MTMark Tehranipoor
Mark Tehranipoor
DFDomenic Forte
Domenic Forte
Reverse engineering of electronics systems is performed for various reasons ranging from honest ones such as failure analysis, fault isolation, trustworthiness verification, obsolescence management, etc. to dishonest ones such as cloning, counterfeiting, identification of vulnerabilities, development of attacks, etc. Regardless of the goal, it is imperative that the research community understands the requirements, complexities, and limitations of reverse engineering. Until recently, the reverse engineering was considered as destructive, time consuming, and prohibitively expensive, thereby restricting its application to a few remote cases. However, the advents of advanced characterization and imaging tools and software have counteracted this point of view. In this paper, we show how X-ray micro-tomography imaging can be combined with advanced 3D image processing and analysis to facilitate the automation of reverse engineering, and thereby lowering the associated time and cost. In this paper, we demonstrate our proposed process on two different printed circuit boards (PCBs). The first PCB is a four-layer custom designed board while the latter is a more complex commercial system. Lessons learned from this effort can be used to both develop advanced countermeasures and establish a more efficient workflow for instances where reverse engineering is deemed necessary. Keywords: Printed circuit boards, non-destructive imaging, X-ray tomography, reverse engineering.

3 April 2015 in Applied Optics
Verified
Journal Article
Closed access
PDF file
KMKaleel Mahmood
Kaleel Mahmood
Pedro Latorre-CarmonaPedro Latorre-Carmona
Pedro Latorre-Carmona
SSSina Shahbazmohamadi
Sina Shahbazmohamadi
FPFiliberto Pla
Filiberto Pla
BJBahram Javidi
Bahram Javidi
Determining the authenticity of integrated circuits is paramount to preventing counterfeit and malicious hardware from being used in critical military, healthcare, aerospace, consumer, and industry applications. Existing techniques to distinguish between authentic and counterfeit integrated circuits (ICs) often include destructive testing requiring subject matter experts. We present a nondestructive technique to detect ICs using x-ray microscopy and advanced imaging analysis with different pattern recognition approaches. Our proposed method is completely automated, and runs in real time. In our approach, images of an integrated circuit are obtained from an x-ray microscope. Local binary pattern features are then extracted from the x-ray image, followed by dimensionality reduction through principal component analysis, and alternatively through a nonlinear principal component methodology using a stacked autoencoder embedded in a deep neural network. From the reduced dimension features, we train two types of learning machines, a support vector machine with a nonlinear kernel and a deep neural network. We present experiments using authentic and ICs to demonstrate that the proposed approach achieves an accuracy of 100% in distinguishing between the counterfeit and authentic samples.