The synergistic effect among flotation agents is why combined flotation agents exhibit superior performance compared to single flotation agents. This research investigates the influence of three surfactants with different charges of polar groups, sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and octanol, combined with dodecylamine (DDA), on quartz flotation. Through the implementation of flotation tests, bubble–particle adhesion induction time testing, gas–liquid two-phase foam properties testing, and surface tension testing, it is revealed that substituting part of the DDA with these surfactants can either enhance or at least maintain the quartz recovery, affect the adhesion induction time, reduce the surface tension of the flotation system, and change the foaming performance and foam stability, depending on their mole ratio in the combined collector. Compared to DDA alone, combining CTAB or OCT with DDA can significantly increase quartz recovery, while SDS with DDA only yields an approximate recovery. Combining SDS or OCT with DDA can reduce the foam stability, while CTAB with DDA enhances the foam stability. The effect of the combination of surfactants and DDA on the adhesion induction time of quartz grains of different sizes with bubbles is the same; furthermore, there is a negative correlation between the adhesion induction time and the recovery, while the foaming properties and stability of foam are positively correlated with the recovery.

Nanostructured tungsten trioxide porous films were prepared by a non-hydrolytic sol–gel method following the inorganic route in which ethanol and PEG were used as the oxygen-donor and structure-directing reagent, respectively. The effects of aging time of the precursor solution, PEG content, and calcination temperature on the structure, morphology, and NO₂ sensing properties of WO₃ films were systematically investigated by using the techniques of X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, and gas sensing measurements. The results demonstrated that a series of WO₃ films with different microstructures could be obtained by manipulating the synthesis parameters. Furthermore, a suitable synthesis condition of WO₃ films for NO₂ sensing application was determined.

Hemimorphite and smithsonite are all-important zinc oxide minerals. The beneficiation and separation of them using flotation method is usually considered difficultly. Minerals surface wettability and its regulation are the core issues in the flotation process, which closely correlate with the surface properties of the minerals. Therefore, an in-depth understanding of the surface properties of the two minerals is of great significance for the study of the flotation technology of them. In this study, the surface properties of the hemimorphite (110) surface and the simthsointe (101) surface, and their relationships to the mineral floatability have been investigated by first-principle calculation method based on density functional theory. The calculation results demonstrated that the hemimorphite (110) surface exhibited more obviously surface reconstruction. For the orbital energy level of the surface atoms of two minerals, the O 2p orbital is closer to the Fermi level than the Zn 3d. Chemical bond Mulliken population value indicated that the ionicity of the unsaturated linkage on the smithsonite (101) surface was stronger than that on the hemimorphite (110) surface. The absolute values of the ratios of negative charges to positive charges on the surfaces of hemimorphite and smithsonite were 1.529 and 1.256 respectively. These results implied that the O atoms on hemimorphite (110) surface are more impede collector molecule, such as hydroximic acid, bond with Zn atom, hemimorphite (110) surface is more readily wetted by water. This study provides comprehension at an atomic level to the relationship between surface properties and the floatability of hemimorphite and smithsonite.

Cerussite is an essential lead oxide mineral with increasing economic importance as lead sulfide resources deplete. This study utilizes density functional theory (DFT) to investigate the structural and electronic properties of the sulfurized cerussite (110) surface. The results show that when the cerussite crystal cleaves along the (110) plane, only the surface layer atoms undergo relaxation to reconstruct the surface, while the atoms located deeper have almost no impact on the reconstructed surface structure. The Pb atoms on the cerussite (110) surface react with the sulfurizing agent to form a PbS deposition layer with a structure similar to galena. This PbS deposition layer is tightly adsorbed onto the lead oxide layer through Pb-S bonds formed by S and subsurface lead oxide structure Pb atoms. The chemical reactivity of Pb atoms in the PbS layer on the sulfurized cerussite (110) surface is more potent than that of Pb atoms on the galena surface; additionally, the Pb atoms closer to the lead oxide layer exhibit slightly higher chemical reactivity than those farther away. This study provides insight into sulfurized cerussite surfaces’ structure and properties at an atomic level and assists in explaining the floating behavior of cerussite.