Drying is the process of moisture removal which is applied to many foodstuffs including fruits and vegetables for preservation and storage purposes. Since solar energy is one type of environmentally friendly renewable energy, open-type solar dryers, natural convective type solar dryers and greenhouse type solar dryers were designed and fabricated in this study for the preservation of fruits and vegetables. A comparative study among various solar drying methods was performed to study the drying performance by maintaining the quality and texture of the dried foodstuffs. Factors such as solar radiation, ambient temperature, moisture in the air, materials used for glazing, inclination, etc., were considered during the fabrication of the solar dryer so that a better estimate of the performance of the solar dryer could be obtained. The lowest drying rate was observed when convective drying was used as an indirect mode of heating. The maximum drying rate observed in open drying was 0.088 kg/kgh, whereas in convective drying under the same conditions, it was 0.03 kg/kgh, which was almost 65% less. This in turn also resulted in the dried samples displaying a better texture and better color. The shrinkage effect on the samples was less pronounced for those samples in the convective dryer than it was for those in the open and greenhouse dryers, as the method uses indirect drying. Comparing convective and greenhouse drying, more shrinkage and a greater browning effect were observed for the open drying method. Out of three types of solar dryers, the greenhouse dryer was selected to study thermal performance because of its better drying rate. DHT11 sensors controlled through Arduino programming were employed in this study to record the temperature and moisture at various locations in the greenhouse dryer setup. The range of energy efficiency of the greenhouse solar dryer was estimated to be from around 15% to 25% on average. This might be due to a greater extent of energy losses. No significant difference was observed in the energy efficiency with respect to the samples used for drying.

In recent times, academicians and scientists have developed many methods for purifying saline water into pure water that is suitable for drinking, as well as other suitable applications. Fortunately, solar desalination has been a very popular technique, which uses eco-friendly solar energy. In this work, a passive-type double-slope solar still was designed and fabricated according to the Global Positioning System (GPS) coordinates of Nizwa city in Oman. Economically and readily available materials, such as acrylic, glass, and foam insulation materials, were used in the construction of the double-slope solar still in addition to the conventional materials used for the supporting structure of the solar still. The climatic factors (such as the solar radiation and ambient temperature), design factors (such as the exposure surface area, inclination, insulation material and thickness, and glazing material), and operating parameters (such as the glass temperature, feed water temperature and yield) obtained were considered in the study to estimate the performance of the solar still. DHT 11 sensors with Arduino programming were used in the experiment to record the temperatures at specific locations on the solar still daily with regular time intervals for a period of 3 to 4 weeks. The solar still was designed to operate from February to March 2023. The temperatures were recorded every two hours daily, whereas the yield was recorded at the end of the day of operation. The quality of the yield was estimated through the measurement of pH and TDS (Total Dissolved Solids) values. The energy and exergy analysis of the desalination unit was carried out to estimate the thermal performance of the system. A significant effect of solar intensity and ambient temperature was observed on the thermal performance of the system and on the quality of the drinking water. An energy efficiency ranging between 30 to 45% and exergy efficiency ranging between 2 to 3.5% was obtained in the system, which was reasonably better for a thermal system involving a renewable source of energy.

In the field of engineering materials, lightweight and ultra-lightweight composites are used in real time to a greater extent, with high-performance targeting for tailor-made systems in aerospace, automotive, and biomedical applications. Sandwich composites are among the most popular lightweight materials used in structural and vehicle-building applications. In the present investigation, one such sandwich composite laminate composed of aluminum face sheets and a high-density polyethylene core was considered to analyze sandwich composites’ flexural and buckling behavior experimentally and numerically. The influence of aspect ratios, such as length to thickness and width to thickness, on the flexural and buckling performance of sandwich composite laminates was explored in the study. Laminates with different widths, namely, 10, 12, and 15 mm, and a uniform thickness and length of 3 mm and 150 mm, respectively, were used for flexural analysis, whereas laminates with widths of 10, 12, and 15 mm and a uniform thickness and length of 3 mm and 350 mm, respectively, were used for buckling analysis. The geometrical influence of the laminates on mechanical performance was studied through performance measures such as critical bending load, flexural stiffness, inter-laminar shear stress, and critical buckling load. A significant influence of aspect ratio on the mechanical behavior of the laminates was observed using both experimental and numerical approaches. Flexural behavior was observed to be better at greater widths, namely, 15 mm, and with a minimum support span of 90 mm due to reduced spring back effects and increased bending resistance. A maximum width of 15 mm allowed for a higher buckling load capacity similar to that of bending resistance. A critical buckling load of 655.8 N seemed to be the maximum and was obtained for the highest aspect ratio, b/t = 5. The soft core and ductile metal face sheets offered combined resistance to both bending and buckling. A lower aspect ratio (span to thickness) rendered these sandwich laminates better in terms of both bending and buckling.

In recent times, fiber reinforced polymer composite materials have become more popular due to their remarkable features such as high specific strength, high stiffness and durability. Particularly, Carbon Fiber Reinforced Polymer (CFRP) composites are one of the most prominent materials used in the field of transportation and building engineering, replacing conventional materials due to their attractive properties as mentioned. In this work, a CFRP laminate is fabricated with carbon fiber mats and epoxy by a hand layup technique. Alumina (Al₂O₃) micro particles are used as a filler material, mixed with epoxy at different weight fractions of 0% to 4% during the fabrication of CFRP laminates. The important objective of the study is to investigate the influence of alumina micro particles on the mechanical performance of the laminates through characterization for various physical and mechanical properties. It is revealed from the results of study that the mass density of the laminates steadily increased with the quantity of alumina micro particles added and subsequently, the porosity of the laminates is reduced significantly. The SEM micrograph confirmed the constituents of the laminate and uniform distribution of Al₂O₃ micro particles with no significant agglomeration. The hardness of the CFRP laminates increased significantly for about 60% with an increase in weight % of Al₂O₃ from 0% to 4%, whereas the water gain % gradually drops from 0 to 2%, after which a substantial rise is observed for 3 to 4%. The improved interlocking due to the addition of filler material reduced the voids in the interfaces and thereby resist the absorption of water and in turn reduced the plasticity of the resin too. Tensile, flexural and inter-laminar shear strengths of the CFRP laminate were improved appreciably with the addition of alumina particles through extended grain boundary and enhanced interfacial bonding between the fibers, epoxy and alumina particles, except at 1 and 3 wt.% of Al₂O₃, which may be due to the pooling of alumina particles within the matrix. Inclusion of hard alumina particles resulted in a significant drop in impact strength due to appreciable reduction in softness of the core region of the laminates.

Solar energy is one of the promising renewable energies; it is clean, green, and accepted worldwide for targeting sustainable development through applications such as power generation, desalination, food preservation, etc. Solar-powered desalination has received more attention in recent times to meet the demand of pure water in the rural places of many countries where solar energy is abundant. In the present work, a double-slope passive solar desalination system was fabricated with readily available materials that can be installed and used in rural places, either for domestic purposes or in small-scale industries. The capacity of the desalination system fabricated to be filled with saline water is ~15 L. The performance of the desalination system is continuously monitored by recording the temperatures at various locations around the system, such as the outer surface of the glass, the inner surface of the glass, inside the basin, and outside the basin, through DHT11 sensors controlled by Arduino programming fed in the Arduino UNO board. The influence of solar radiation intensity and temperatures at various locations on the solar still on the thermal performance and production of desalination unit is analyzed by the data recorded by the Arduino program. A cumulative yield of fresh water of around 0.7–0.9 L is recorded every day, and the lowest yield of around 0.55 L was obtained on the third day of experimentation.